Hot Rods Jerry 's 32 5 Window Project

Sent from my SAMSUNG-SM-G891A using The H.A.M.B. mobile app

 

Sent from my SAMSUNG-SM-G891A using The H.A.M.B. mobile app

 

New bottom and lower skin on door. Gaps getting dialed in



Sent from my SAMSUNG-SM-G891A using The H.A.M.B. mobile app

 

Jerry, This is looking very bad ass......kadoos to you and Andy for all the skills...Keep on doing what your doing....

 

Sent from my SAMSUNG-SM-G891A using The H.A.M.B. mobile app

 

Just about buttoned up..garnish moldings next

Sent from my SAMSUNG-SM-G891A using The H.A.M.B. mobile app

 

Beginning to look like it came from the factory chopped

 

Rock !

A

 

Looking great and moving right along my friend.....Keep it going.

 

New Drip rails on and pinholes on top of cowl under windshield welded up



Sent from my SAMSUNG-SM-G891A using The H.A.M.B. mobile app

 

Looking nice fellas.

 

Sent from my SAMSUNG-SM-G891A using The H.A.M.B. mobile app

 

Sent from my SAMSUNG-SM-G891A using The H.A.M.B. mobile app

That really puts the chop in perspective I think.

 

Nice work Jerry. How many dropped axles have you painted on that floor? [emoji41]


Sent from my iPhone using The H.A.M.B. mobile app

 

Nice work. Wondering how you attached the new drip rails? Spot weld from inside of the roof?

 

Just checking in and it looks amazing. I think you should do a separate thead on the louvers. How to make the tool and then use the tool for stamping.

 

That's Andy Kohler's floor. The garnish moldings are going to be chrome plated so He's tigging them up for me. After, I'll sand and prepolish...getting a bit fancy pantsy on this one. I believe his floor has seen quite a few dropped axles

Sent from my SAMSUNG-SM-G891A using The H.A.M.B. mobile app

 

I just might

Sent from my SAMSUNG-SM-G891A using The H.A.M.B. mobile app

 

Holes were drilled in drip rail channel, weld through primer was applied, and drip rail was clamped on and plug welded from the inside.


Sent from my SAMSUNG-SM-G891A using The H.A.M.B. mobile app

 

I'll second that request.

 

Experimenting with an idea this morning for my headlights..we'll see if it works out.


Sent from my SAMSUNG-SM-G891A using The H.A.M.B. mobile app

 

Lots of sanding and polishing to go but came out pretty neat. I acid etched an art deco pattern into a pair of brass headlight buckets for the new car I'm putting together. I'm going to polish the raised beams ..then tape them off and blast the whole bucket. After the tape is pulled I'll have an even matte finish on the buckets and a polished raised design. They did this on saxophones in the 1920's and 1930's



Sent from my SAMSUNG-SM-G891A using The H.A.M.B. mobile app

 

Little hand polish ..you can really see how deeply the pattern is etched into the brass buckets




Sent from my SAMSUNG-SM-G891A using The H.A.M.B. mobile app

 

very cool, I like a lot.......

 

Also cleaned up the glass markers with some 3000 grit


Sent from my SAMSUNG-SM-G891A using The H.A.M.B. mobile app

 

I'm all for different,but this one gives me pause.Maybe Too much going on???


Sent from my iPad using The H.A.M.B. mobile app

 

Yea I agree!

Sent from my SAMSUNG-SM-G891A using The H.A.M.B. mobile app

 

Not that Jerry needs anyones approval, especially mine, but I like everything I've seen.
I opened my mouth before I fully knew Jerrys' skilset and I'm looking forward to how the front sheetmetal turns out.

 

No sweat Denny ...ive got a few hood ideas

Sent from my SAMSUNG-SM-G891A using The H.A.M.B. mobile app

 

Sent from my SAMSUNG-SM-G891A using The H.A.M.B. mobile app


While I'm getting the headlights squared away, Andy tig'd the garnish moldings up. I'm going to send these out for chrome and a tig seam is so much easier to blend. He did a great job. Im going to pre polish them then send them out for a shiny dip.