Pay it foward = free parts for HAMB members

looking for any remains of the rear sides of a 30/31 5 window...something some one cut off for new or???is rusted and they found something bettrer????or??????? i have quite a few itms could go forward.........sbc nos oil pumps, good heads sbc valve covers M/T finned.......

maybe we should remane this thread to

Pay it/Swap it / forward............

 

Desoto Power flite transmission from a 55 desoto, might fit 54 56 57 Plymouth Chrysler Dodge... Has the parking brake on theback... Going to the boneyard soon, if you can pick it up it's yours... Stow Mass.

See my sig. for want.... pix attached...

PM direct, I don't watch this thread often.

 

interested in the aircleaner Novatattoo

 

I was notified that I am recieving SMALL CARB AND A SHORT TAIL SHAFT SECTION, So I need to pay it forward, does anybody need any of my stuff I got posted? Karma is a good thing I will look and see if I have some other stuff to help out the cause..Ryan

 

Early Ford Dating Service....

Hey...anyone have a lonely right side 48 Ford car style spinster...I mean SPINDLE with good bearing surface/threads????
A bit sloppy in the main bushing is fine...you'd expect that after a life on the streets.
Doesn't even have to have two eyes...one would be fine by me!

"Lefty" and I could sure give her a good time....I mean HOME!

We'll treat her REAL good...I promise!!!

 

BIG HUGE THANKS TO DOUBLE CADDY FOR THE CARB.. Now I just need to return the KARMA to SOMEone.. I have sent several things to guys in the past 54 chev Hinge Spring, Trans DATA PLATE FOR a 49 Ford TRUCK , Stainless trim for a 54 Chev, before this PAY IT FORWRD THREAD STARTED, I mean is'nt this what its all about is helping each other out, lets keep it up guys, and a huge thanks to DOUBLE CADDY you just made my day.... Ryan

 

Irs 30

I could use that model A window crank.

I have a couple items I could part with as well;

1955 Chrysler New yorker rear end (pick up only)
331 hemi motor mounts from same car.
Some stainless trim, Complete roof sheet metal and trunk lid.(same car-4 door)

 

Sorry maybe I have that worded wrong, I need one don't have one to offer, sorry..I will check my post and edit it if its wrong,..Ryan

 

My bad, should have read closer.I am going to a Model A swap this weekend, maybe I'll find two of them.

 

more to go ...Eelco Rader Single Rib 14x6 4 3/4 bolt pattern,,will need rechrome

Looking for Ford Steering arm/hoop
and a single ( 1/2 ) a wishbone ,,see above post

 

Glad to have helped.
Todd

 

3 speed manual tranny from a 63 Ford Econoline 6 cyl. I was told no problems.
This is not real light but it is clean, pick up in Vegas or I will ship on your $.
GONE

 

HUGE THANKS to LOBUCROD For the 350 turbo short tailshaft section, now I just need to find a slip yoke for this thing and I am in business... Thanks Again Ryan

 

Can anyone tell me if this tranny will bolt up to a 57 392 hemi?

 

I've got a running 1950 216 w/3 speed trans...all working. I took them out to put an SBC in my Chevy. It also has a new air filter *not pictured*. The carburetor needs a little work.



What I'm looking for:
-Nice 4bbl carburetor, automatic choke for my SBC
-patch panels for the front floor, rockers, and rear quarters
-driver's side door 49-52

 

I've got a 650 holley with vac sec. and a q-jet with secoundary problemsthey bind a bit at first so it doesn't completly close

 

Das motor is yours. We'll finish our dealin's on PM

 

2 - 1932/42 PU and Wagon 12volt tail lamps. - GONE
Sacramento ford - 35-36/39pu Headlamp wiring and sockets.
Holley fuel pressure regulator 4-9lbs 3 connections. - GONE
Summit - fuel pressure guage. 1-15lbs. - GONE
About 3ft of braided fuel line. -GONE
53' ford trunk lock w/ keys.
1 - Dicks SBC oil cap - GONE
Speedway 3 inch lower blocks - note*** these are wider then what could be used on my 53'. - GONE
Bob Drake (new never installed) 46-48 radiator cover.

I'll mail things out if anyone pm's me. Won't promise it'll be fast.

 

I could use the taillamps

I'll come up with something to make available

 

Les PM'd you back.

 

hipkatgreaser, I'll take the holley 650

 

ill take the blocks if not spoken for..

 

I have some cab corner patches for a 72 Chev GMC Pick-up left and right NEW NEWNEW if anybody needs them, may fit other years, pm me for details..

 

i have a pair of ansen 3.5 x 15 aluminum slots (ya know the vintage gasser wheels) with new bias ply rubber on them from back in the day, the odd thing is the bolt pattern its small early mopar 5 lugs on 4 inch bolt circle. ive seen these go for a bunch on egay and wud be glad to trade them for a used msd 6al that works or ? whatcha got ? im hevy into desoto high deck hemis and got a ton of other shit, what do you need ? pm me . this is what hot rodding is all about great idea

 

I have a set of mostly complete rear brake stuff for 53-54 chevy: drums, cylinders, keepers, emergency cables - no shoes. This is sort of heavy, but send me and address and cover the shipping and its yours

PM me - I dont check this thread enough

 

Holley spoken for still have q-jet it is in workin order just needs a little help

lookin for grill and misc. front and rear trim for a 64 belair 4 door

 

I have a cowl for a 31? Chevy truck. Its allright shape with a little rust in the one corner. I'm In ND But have a truck going to Mpls next week. I can get anyone some pics tomorrow if they want.

 

I have an older autopuse 12 VDC fuel pump and NOS brand fuel pump that I didnt end up using .

 

I have a 53 Chevy 210 rear bumper, dent's and dings in it, and chrome is flaking off. Partial rear "push bar" goes with it.

Local pick-up only, sorry

 

found the picture of the NOS pump