Pic request....Rare SBC speed equipment.

holy crap...that's pretty nice vrod....that's some Ferrari lookin' stuff right there, mand that'd be sweet to see on the road

 

The Moon Weber side-draft manifold was/is(you can still buy one special order) welded from several castings too.

 

Holley Pro Dominator for a SBC. Lots of them built, but only a few hundred for the SBC.

 

Here is a pair of modified Inglese valve covers for SBC.

 

Here is an NOS pair of Ralph Ridgeway (of Ridge Runner tunnel ram fame) valve covers. Super hard to find. I've only seen one set in my life (this set that I recently sold).

 

These fit what????

 

^^^^sbc

 

I think you may be referring to the Leo Lyons heads - basically an Ardun adapted to the SBC. They were made in Riverside CA ca 1965. I passed on a pair back in the 1990s and then had no money when a complete engine with the heads came up about five years ago. Don Marks at House of Pain in AZ has been doing stuff for these for a while.

 

Yes they are for small block Chevrolet.... thats why they are posted in this thread. They are on ebay right now if you want more pictures

 

Here is a single carburetor "cross ram" style intake manifold. It is a McFarland Tork Link. Used on the dirt tracks. Suppose to make a lot of torque around the 4,000 rpm mark.

 

Here are three (semi) rare cross ram manifolds for SBC. Pictured from left to right.

Offenhauser 360* with removable top. (Single 4 lid pictured as well).

Edelbrock STR-10 with removable lid.

Edelbrock XC-8.

 

Last one for now:

Early Weiand "Say Why-And" for SBC.

 

Front drive distributor of a friend .

 

Anyone have a picture of a Cam-A-GO unit for the SBC? It was a variable valve timing setup made by OMEC and sold through Offenhauser during the late 1960's and early 1970's.

 

Just a note, the offy crossram linkage can still be ordered from dmarv at exeter auto....

 

Shot at 2008-09-18

i know what it is and i have seen 100's of them as well but i have only ever seen 1 for a small chevy motor ! but if they are common where you are and you know of some for sale i'll take em, cause their have been a couple ads in the wanted section on here for a few years looking for these for SBC and none have turned up available yet! !!!

 

Vintage Roto-Faze distributor.

 

Vintage "Say Why-And" Weiand single carburetor tunnel ram.

-Matt

 

Edelbrock X-C8 Cross Ram. Don't know if it's rare, but haven't seen one posted here yet. If I ever find a '55 Chevy, I'm building a gasser with it.

 

Wait, I see a mention in the top post. Oops.

 

the due look like cal customs i had a set on a 57 chevy about 1970

 

I have a Creitz dual four barrel intake, a set of early Mickey Thompson small journal aluminum rods, an Edelbrock cross ram, a TR 1 tunnel ram, a "way bitchin'" Eelco oil pan, some cool Hilborn, Weiand, and Enderle timing covers, and Isky blower drive parts. Probably have some other stuff buried somewhere...

 

Let's see some pictures!!..

 

Enderle injection

 

Anyone got a set of Mr Gasket clear plastic valve covers for s sbc? Lippy

 

Is that anything like the clear distributor caps???

 

Here's a pic of the box from Mr. Gasket...


And here's a pic of the actual VC's.

 

I have a set too. Someone painted the inside of one. Got the decals?

 

I just sold a M/T scattershield for a sbc.

 

Fill the inside of the painted valve cover with Castrol Super Clean straight out of the gallon container and let it sit for a couple of days... It should eat that paint up without hurting the plastic...