Features Doing Falcons Right

selling my n.o.s. cal custom spider caps too. they are dusty right off the shelf

 

Sent you a PM

Posted using the Full Custom H.A.M.B. App!

 

this is a local car in my area, I hope to get more, an better pictures of it this year.



another PNW car I like quite a bit, not sure if the owner is on here or not, but at any rate

 

Found some Falcon motor compartment shots to share...

 

Hey Longroof, are those intake pipes copper?

 

not all too positive on that one, at first I thought it had been chromed and then sanded off, but it used to just have like a smoked clear powder coat on it so it may be.

 

I remember seeing that one at Jubitz, but haven't seen the other one around.

 

Karl,
More pictures of that car here:

http://www.911motorsports.net/galleries-project-vehicles/4581696833

 

????? i bought my 63 1/2 sprint with new windshield installed but chrome trim came in a box. Does windshield have to b removed to install chrome. Any help is appreciated

 

Unfortunately the window has to come out to install the lower piece of chrome trim. The sides and the upper chrome can be installed after the glass is in

 

Thanx for reply. info much appreciated. was afraid that was the case. hate to pull a new shield but gotta have chrome installed. building a 60's gasser. I enjoy the site. keep the falcons flying.

 

yea the other is down here in central Oregon

and you are correct on the green one, that's where I took the picture.

 

So I had a persistent intake coolant leak that I decided was the fault of the Fel-Pro 1250 Print-O-Seal intake gaskets that I've been using on various SBF's for many years without a problem...



As it turns out, my trusty Weiand street fighter intake was bent....warped .008 in the middle.



So I figured it was time for a change and got an Edelbrock 7521 air gap.
The Edelbrock intake gaskets suspiciously looked a lot like the Fel-Pro 1250 Print-O-Seals.
With an Edelbrock logo.



Now I'm just waitin' for the glue ta' dry...



It's supposed to be in the high 60's next week. I think January might finally be over on the right hand side of the country..

 

Nice motor! I know what you mean on vacuum leaks, chased one for a long time myself.. don't miss those days!

 

I should'a been more specific- it was a coolant leak... I'm laffin' here.

Not at you though; me.

 

anyone looking for a radio delete for their 62-63 futura? new old stock piece

 

Just sent you a PM...


Posted with an IBM Selectric

 

Evil, Sent you 2 PM,s on the delete plate please ck.

Thanks: Butch Evans
Thomasville NC

 

Is anyone running their stock '60-'64 FM2 column shifter with an AOD transmission? I read elsewhere that the C4 detent sold by Falconparts.com will work with an AOD, but I didn’t find any more details. I’m having trouble finding a T5 for my ‘62 and since I have all the automatic parts, I’m researching the possibility of running an AOD behind the 250 instead.

Thanks for any help!

 

Yup, I'm currently running an AOD with the C-4 detent plate on my column shift 63. Works fine, it's just a little fiddly to change with the square headed bolts while working against the spring pressure for the column linkage inside the tube. I've got a picture some place....


Posted with an IBM Selectric

 

Great! This was explained to me by another fellow who indicated that his 1983 AOD was set up so that one could not manually select second gear - is that the same for yours?

Thanks!

 

Well, kinda' correct- with the Cruise-O-matic detent plate, it's impossible to manually select the AOD's 2nd gear (on an AOD, this is first gear until it shifts into second...thus the infamous "AOD shuffle" on floor shifters)...

It'll work fine with the old detent plate, you just can't manually select any gear lower than third...

You'll also have to make some sort of linkage- My 63 had a half ass conversion when I got it- I ditched most of the linkage that was on the trans but saved some of it:




I'll spare you the usual TV cable/pressure warning....

 

By "old detent plate" you mean from the FM2? Giving you P R N O D where the FM2 gave you P R N D 1?

 

With AOD-

Original plate gave me P R N O/D 3

C-4 detent plate gives me P R N O/D 3 2

I never select anything other than O/D anyway-

I've got a trick Silver Fox constant pressure valve body, 2400RPM stall converter, Trans-Go governor and a bunch of heavy duty crap in my AOD.

More info here:

http://www.jalopyjournal.com/forum/showthread.php?p=8656081#post8656081

 

Thanks again. Sorry for the dumb questions. I've never done much studying about automatics until this week.

 

No sweat, dude. It was hard for me to wrap my head around the fact that there is no manual 1st gear select on AOD's.

Go over to "Click Clack Racing's" forum for everything you ever wanted to know about Ford automatic overdrive transmissions but were afraid to ask.


Posted with an IBM Selectric

 

Has anybody tried to eliminate some of the steering wheel play in their falcon?


Posted using the Full Custom H.A.M.B. App!

 

Yeah, rebuild the steering arms, ball joints, etc. to tighten it up, and then adjust the play in the steering box. If that doesn't do it, it probably needs a steering box rebuild or replace.

 

Actually, I have found the best place to start is almost always with an idler arm rebuild kit. It has a rubber bushing that I firmly believe about half of were bad before they left the dealer show room. The kit costs about 15.00 at any parts wholesaler.

 

I've been looking for a 60's sedan delivery for some time now and fortunately found one,the aussie deliverys don't have the long doors,where the American models do I'm a big bloke and need that extra space.I intend to do a few mods,my q/s is,will the convertible door bolt up and will the rubber seal on the conv/top mate up with the door frame on the delivery,thanks for your time and hope you can help ,Gaz!