Summer 2010 - Rolling Chassis

1931 Chevy 2-Door Sedan with a 67' Chevy Van I-Beam / 96' 8.8 Ford Explorer Rear Axle with 3:55's & Traction Lock / 86' Monte Carlo 305 / 79' TH400 Auto - and for the most part it has all been FREE!

Guns, Lexan, Aluminum and Rivets EVERYWHERE! - This is the "THEME" of Evelyn my 1931 Chevrolet Tub.. Enjoy the pictures...

Rob in NH

Guns, Lexan, Aluminum and Rivets EVERYWHERE! - This is the "THEME" of Evelyn my 1931 Chevrolet Tub.. Enjoy the pictures...

407

22 Dec 2010

I looked high and low for a Banjo only to find that my neighbor had this 1937' Ford unit sitting on his shelf doing nothing.. Can you say FREE?? - I have since shattered off all the cracked Bakelite and will replace it with CNC cut Rock Maple along with casting my own cover for the center in aluminum..

Rob in NH

Summer 2010 - Rolling Chassis

I looked high and low for a Banjo only to find that my neighbor had this 1937' Ford unit sitting on his shelf doing nothing.. Can you say FREE?? - I have since shattered off all the cracked Bakelite and will replace it with CNC cut Rock Maple along with casting my own cover for the center in aluminum..

372

22 Dec 2010

This is what it looked like sitting together a few years ago.. Basically some 2x4's are holding the rear-end UP! - The rear lights are aftermarket Corvette and have been Frenched-In a while ago..

Rob in NH

Summer 2010 - Rolling Chassis

This is what it looked like sitting together a few years ago.. Basically some 2x4's are holding the rear-end UP! - The rear lights are aftermarket Corvette and have been Frenched-In a while ago..

372

22 Dec 2010

Half-Way into the project I was collecting ODD parts and setting it all together for It's FIRST mock-up.. This picture is YEARS old as I was in a Wheelchair for 4.5 years due to a major Car accident.. :^(

Rob in NH

Summer 2010 - Rolling Chassis

Half-Way into the project I was collecting ODD parts and setting it all together for It's FIRST mock-up.. This picture is YEARS old as I was in a Wheelchair for 4.5 years due to a major Car accident.. :^(

380

22 Dec 2010

Grille is from a 35' Chevy Truck (FREE) It was chopped 4" inches later on.. What you see it it sitting in place and supported by a scrap of bedrail steel as I had nothing at the time.. The garage was NEW and completely empty and lacking in Tools..

Rob in NH

Summer 2010 - Rolling Chassis

Grille is from a 35' Chevy Truck (FREE) It was chopped 4" inches later on.. What you see it it sitting in place and supported by a scrap of bedrail steel as I had nothing at the time.. The garage was NEW and completely empty and lacking in Tools..

356

22 Dec 2010

Juat a Dummy Engine and Hollow Transmission for the Mock-Up.. I was slowly bringing home parts from a friends Junkyard as time (and trash) allowed.. But I was able to design the Frame with all the Junk and it was later returned to where it came from as better goodies came in...

Rob in NH

Summer 2010 - Rolling Chassis

Juat a Dummy Engine and Hollow Transmission for the Mock-Up.. I was slowly bringing home parts from a friends Junkyard as time (and trash) allowed.. But I was able to design the Frame with all the Junk and it was later returned to where it came from as better goodies came in...

377

22 Dec 2010

TH400 (FREE) in position and bolted up..

Rob in NH

Summer 2010 - Rolling Chassis

TH400 (FREE) in position and bolted up..

346

22 Dec 2010

Day ONE in the Garage she looked like this.. ROTTED BAD.. So don't let the pictures FOOL you..

Rob in NH

Summer 2010 - Rolling Chassis

Day ONE in the Garage she looked like this.. ROTTED BAD.. So don't let the pictures FOOL you..

377

22 Dec 2010

CAM Bumper? - The local Car-Club back in the day was the "Cam Twisters" so I found it appropriate to have a Cam as my frame connector out front.. The Frame is also heavily supported behind the Radiator so the Cam is just for the "LOOK"

Rob in NH

Summer 2010 - Rolling Chassis

CAM Bumper? - The local Car-Club back in the day was the "Cam Twisters" so I found it appropriate to have a Cam as my frame connector out front.. The Frame is also heavily supported behind the Radiator so the Cam is just for the "LOOK"

321

22 Dec 2010

Rob in NH, Dec 22, 2010

Page 1 of 2

Album Comments

There are no comments to display.

Show Ignored Content

Top

Log in or Sign up

Summer 2010 - Rolling Chassis

Rob in NH

Guns, Lexan, Aluminum and Rivets EVERYWHERE! - This is the "THEME" of Evelyn my 1931 Chevrolet Tub.. Enjoy the pictures...

Rob in NH

Rob in NH

This is what it looked like sitting together a few years ago.. Basically some 2x4's are holding the rear-end UP! - The rear lights are aftermarket Corvette and have been Frenched-In a while ago..

Rob in NH

Half-Way into the project I was collecting ODD parts and setting it all together for It's FIRST mock-up.. This picture is YEARS old as I was in a Wheelchair for 4.5 years due to a major Car accident.. :^(

Rob in NH

Grille is from a 35' Chevy Truck (FREE) It was chopped 4" inches later on.. What you see it it sitting in place and supported by a scrap of bedrail steel as I had nothing at the time.. The garage was NEW and completely empty and lacking in Tools..

Rob in NH

Juat a Dummy Engine and Hollow Transmission for the Mock-Up.. I was slowly bringing home parts from a friends Junkyard as time (and trash) allowed.. But I was able to design the Frame with all the Junk and it was later returned to where it came from as better goodies came in...

Rob in NH

TH400 (FREE) in position and bolted up..

Rob in NH

Day ONE in the Garage she looked like this.. ROTTED BAD.. So don't let the pictures FOOL you..

Rob in NH

CAM Bumper? - The local Car-Club back in the day was the "Cam Twisters" so I found it appropriate to have a Cam as my frame connector out front.. The Frame is also heavily supported behind the Radiator so the Cam is just for the "LOOK"

Can View Media:

Can Add Media:

Archive

Atomic Industry

Support

Subscribe

Summer 2010 - Rolling Chassis

Sort By...

Type Filters

Useful Searches

Archive

Atomic Industry

Support

Subscribe