Register now to get rid of these ads!

Technical Model A spreaderbar add much improvement?

Discussion in 'Traditional Hot Rods' started by BLACKPRIMERFAN, Nov 7, 2015.

  1. BLACKPRIMERFAN
    Joined: Oct 4, 2009
    Posts: 114

    BLACKPRIMERFAN
    Member
    from OH/MI LINE

    I'm putting the finishing touches on my boxed model A ch***is. I prefer the look of the plain front frame horns without a spreaderbar. Does the front spreaderbar really make a noticeable difference in driving characterists or ch***is strength?
     
  2. Hitchhiker
    Joined: May 1, 2008
    Posts: 8,507

    Hitchhiker
    Member

    I would bet with a boxed frame...no.
     
  3. With a boxed frame.... A bolt in spreader bar is only for looks.
     
  4. mad mikey
    Joined: Dec 22, 2013
    Posts: 9,425

    mad mikey
    Member

    The only purpose mine serves on my boxed frame is mounting for the EELCO fuel tank.
     
  5. -Brent-
    Joined: Nov 20, 2006
    Posts: 7,847

    -Brent-
    Member

    Even with an unboxed frame I couldn't see it providing any benefit since it's so close to the front crossmember.
     
    volvobrynk and clem like this.
  6. Dean Lowe
    Joined: May 20, 2008
    Posts: 22,042

    Dean Lowe
    ALLIANCE MEMBER

    I have run boxed, and unboxed Model A frames. A spreader, bolted in, or welded in, has no effect on the frames function at all. IMO a spreader on a Model A adds absolutely nothing at all in the appearance department either. If you are running a race car, you need a place to mount a race tank. If you are running a street car, you don't need the tank and everyone, who matters, knows it's phony. Opinion from an old Model A drag racer.
     
  7. X38
    Joined: Feb 27, 2005
    Posts: 17,498

    X38
    Member

    Model A's don't have a spreader bar.
     
    gwhite and clem like this.
  8. gnichols
    Joined: Mar 6, 2008
    Posts: 11,412

    gnichols
    Member
    from Tampa, FL

    More of a bumper, in a way... might keep the rac****s and other varmints off your radiator. Gary
     
  9. clem
    Joined: Dec 20, 2006
    Posts: 4,681

    clem
    Member

    Where will you hang your number plate with out one ?
    As stated above, Model A s didn't have a spreader bar.
    (and is cosmetic only on '32 fords, although they may have been used to 'spread' the ch***is rails while the crossmembers were fitted.
    I made my rear one extra heavy to act as a bumper and to prevent damage to petrol tank in case of a rear collision.
     
    volvobrynk likes this.
  10. BLACKPRIMERFAN
    Joined: Oct 4, 2009
    Posts: 114

    BLACKPRIMERFAN
    Member
    from OH/MI LINE

    Thanks to all that replied... Sounds like an accessory not a necessity.
     
  11. HOTRODPRIMER
    Joined: Jan 3, 2003
    Posts: 64,747

    HOTRODPRIMER
    ALLIANCE MEMBER

    This is my old Model A pickup from back in the 70's,note no speader bar. HRP

    [​IMG]
     
    kevinwalshe likes this.
  12. seb fontana
    Joined: Sep 1, 2005
    Posts: 9,196

    seb fontana
    Member
    from ct

    I would run one, looks better [fills in the void] and can hold turn signals..
     
  13. verde742
    Joined: Aug 11, 2010
    Posts: 6,588

    verde742
    Member

    I have never run one, on a Model A, save them for yer 32..
     
  14. I installed one for a tag mount
     
  15. -Brent-
    Joined: Nov 20, 2006
    Posts: 7,847

    -Brent-
    Member

    I have seen them on Model As in pics from way back. It's not that folks didn't fab them, they did, the question was if they served a purpose, structurally - which they don't.
     

Share This Page

Register now to get rid of these ads!

Archive

Copyright © 1995-2021 The Jalopy Journal: Steal our stuff, we'll kick your teeth in. Terms of Service. Privacy Policy.

Atomic Industry
Forum software by XenForo™ ©2010-2014 XenForo Ltd.