Got some pics from JB at the upholstery shop yesterday. The Radio Flyer wagon is now complete. He was initially going to do tan upholstery, but when he laid the red against the wagon he said the wild color won out. Better match to the build. So this little wagon was painted in Leonardtown MD, lettered and striped in Hummelstown PA, and now upholstered in Lexington SC. It really gets around..
JB built it for his niece and nephew. They live in SC amongst all the red clay. Yes, we laugh about the situation too.
Love all the details along the way that take this car to a level most of us can only dream of. Thank you for taking the time to keep the thread updated along the way - I know I, and I suspect many others have learned a LOT from following along and studying your techniques and solutions. Can’t wait to see the completed car.
Been playing catchup for a while since my cross-country venture for the new shop truck, time for some long overdue updates. Finishing up on our tailgate, the last stainless pieces of the puzzle came from McMillan Rod and Custom in WI. Pretty good source for polished stainless trim pieces... We had emailed them dimensions for existing holes in the tailgate, and the welded studs were spot on. All our stainless parts added for a test fit/pre-drill/pre-screw of all the hardware to insure they'd go in straight during final assembly. Here's my contribution to the upholstery effort on the car.... And our tailgate installed.... And our update would not be complete without the requisite back up and punt moment. As we were closing the tailgate there was a slight binding as the tailgate was all but closed. Hey, you know my luck by now. Seems our trial fit in bare metal showed no issues but now we had multiple layers of paint that didn't want to play nice. The hinge notches in the bottom of the tailgate skin were digging into the inside of the hinges.. At this point a hinge is an easier repair than a completed tailgate, so the hinges were milled down .080 on that face and the countersunk holes deepened that much as well.. Then about three rounds of epoxy, block, repeat to eliminate the casting flaws, and on to the organic green kandy basecoat once more... And then groundhog day, install it once more, with much better results this time.
Well, it's about high time we got back on the console... We had designed the "hoop" to go around each leg of the horseshoe shifter, and to hold bulb seal rather than a strip brush, for a cleaner look. When we ordered the shifter it came with the new clear bezel for gear indication, but since we didn't have the factory console and it's matching parts, it was a bit much for us to incorporate into our fabricated console. In an attempt at simpler is better, one of the hoops was made with a wider flange for adding gear indicator nomenclature. Well, we have been waiting awhile for our turn in line at the machine shop, and that day finally arrived Next was the layout of the locations... The ends of the slots were cut using a 5/8 diameter RotaCut, joined together between with a Milwaukee M18 14 ga shear, and trimmed afterwards using Wurth snips. https://youtube.com/shorts/vA83vJVWnSY?si=vIKUzlgmDHCVFgM7 Then the 4-way power window switch was added to the rear, using the same process. And lastly, our AC vents added. I didn't have any RotoCuts in the 2-1/2 diameter, so we opted for using a hole saw. They can be sketchy when cutting through sheet metal, with the pilot drill wanting to pull the hole sideways. So we sacrificed an extra holesaw arbor to make a bolt-in guide, and changed the pilot bit out for a piece of 1/4 round stock. Holes deburred and vents installed.. Final version https://youtube.com/shorts/P94H8M4Uti0?si=JgYffFOc_l96Whkg https://youtube.com/shorts/6lWksNqKvXI?si=JMsE_F7LUX7CDUhV
Why did you put the indicator on the passenger side and not the drivers side where it can be seen easier?
initially that’s where we had it going but that would put the left escutcheon closer to the edge than the right, making it appear off center. The way it is done now you don’t notice that, and given the vantage point from the drivers seat it’s just as legible from either position.
The Jalopy Journal
