Register now to get rid of these ads!

Customs Will this make it to LSRU?

Discussion in 'The Hokey Ass Message Board' started by Bob K, Jan 23, 2010.

  1. Bob K
    Joined: Mar 3, 2001
    Posts: 5,772

    Bob K
    Member Emeritus
    from Antigo Wi.

    Started the repaint process this week. It had too many "Badges of Honor" and some rust issues, 97k plus being at B'ville for the last 5 years took it's toll. It must go to the upholestry shop on March 15th and then we leave for the Round Up on the 5th of April.
    Will it make it? I think so, it's not as bad as it looks.

    [​IMG]
    There was some bubbles where the pan was welded to the body.


    [​IMG]
    The leaded seam cracked from underneath, I have never seen that before.


    [​IMG]
    There were a ton of stone chips and we found some rust in this area


    [​IMG]
    The p***anger door and fender dog leg had some rust, cut it out and used POR 15 before putting the patches in.


    [​IMG]
    We decided to tighten up the gap on the rounded hood corners.


    [​IMG]
    There is a dent about the size of a silver dollar in the p***anger side of the hood that we have to deal with yet and a dent in the drivers door that came from some fat *** trying to close the door with his big fat ***. He shall remain nameless but his initials are Bob K.

    I hope we didn't bite off too much but I think we will make it.

    BTW I don't do my own body work, I am very fortunate to have a guy that works at the local Chevy dealership come over about 8 hours a week when needed to handle that part of the job. My buddy Steve is also a huge help with the other stuff.

    B:)B
     
  2. 3wLarry
    Joined: Mar 11, 2005
    Posts: 12,804

    3wLarry
    Member Emeritus
    from Owasso, Ok

    man, I can see that in deep liquid black...:)
     
    kidcampbell71 likes this.
  3. John Denich
    Joined: Nov 20, 2005
    Posts: 2,718

    John Denich

    You better!!! I need a tour guide!!!
     
  4. No doubt about it Bob.
    Later,
    ****
     
  5. stillrunners
    Joined: Aug 27, 2009
    Posts: 10,593

    stillrunners
    Member
    from dallas

  6. milwscruffy
    Joined: Aug 29, 2006
    Posts: 4,191

    milwscruffy
    ALLIANCE MEMBER

    How long did it take to plastic coat the inside of the garage? Good luck and make sure you have plenty of liquid refreshments to help wash down the dust and keep hydrated.:D:D:D Steve
     
  7. Now keep your "fat ***" door closer off of it when it's finished and you'll get another 95k out of it! Hello from the warm country, Aridzona! Crow
     
  8. MercDeuceMan
    Joined: Jul 19, 2004
    Posts: 1,933

    MercDeuceMan
    Member
    from Indiana

    What color will the new paint be Bob?
     
  9. resqd37Zep
    Joined: Aug 28, 2006
    Posts: 3,215

    resqd37Zep
    Member
    from Nor Cal

    She's looking good. The Devil's in the details and the little things will kill ya everytime. Looks like you got it under control though.
     
  10. mark 55
    Joined: Oct 12, 2006
    Posts: 110

    mark 55
    Member

    I hope the car makes it, but there better be no doubt about the owner being there. It wouldn't be the same without you, ya big cheesehead!
     
  11. Hey fatas--I mean, Bob....is the same guy spraying it that did it last time? Hope he does--it sure was nice. That boy does some fine work :cool:

    I miss ya, old man ;) xoxoxo
     
  12. ratster
    Joined: Sep 23, 2001
    Posts: 3,629

    ratster
    Member

    goodluck bob, you can do it
     
  13. geemann51
    Joined: Dec 16, 2001
    Posts: 2,119

    geemann51
    Member

    It better... Go Bob Go!
     
  14. hiboy32
    Joined: Nov 7, 2001
    Posts: 2,797

    hiboy32
    Member
    from Omaha, NE

    Wow, what a concept. DRIVE it, then after a few years, repaint it. I love it. I always know that I am at the most happening events when I see that green convert.
     
  15. Anderson
    Joined: Jan 27, 2003
    Posts: 7,560

    Anderson
    Member

    Gonna go two tone yellow and orange this time Bob?
     
  16. Gerg
    Joined: Feb 27, 2006
    Posts: 1,828

    Gerg
    Member

    look good bob as always !
     
  17. Da Tinman
    Joined: Dec 29, 2005
    Posts: 4,222

    Da Tinman
    Member

    not that my opinion matters, but,,, that car needs to be green.

    it'll look fantastic in any color, but the green is perfect for it.

    Looking good!
     
  18. Progress is being made, I see. Even with the best of care, stuff happens
    to cars. My money is on you and your body man to get er done in time.
    That dark green is a nice color.

    Bob T
     
  19. SlowandLow63
    Joined: Sep 18, 2004
    Posts: 5,958

    SlowandLow63
    Member
    from Central NJ

    Damn Bob good for you! That car looked so sweet I never noticed any of the trouble spots, too busy getting lost in that deep dark green! Good luck w/ it.
     
  20. FWilliams
    Joined: Apr 24, 2001
    Posts: 1,986

    FWilliams
    Member

    you'll make it Bob:)
     
  21. Rusty
    Joined: Mar 4, 2004
    Posts: 9,487

    Rusty
    Member

    Atleast you got a badd *** vette to drive down if it dont make it!!!
     
    Last edited: Jan 25, 2010
  22. DonMan
    Joined: Sep 7, 2007
    Posts: 981

    DonMan
    Member

    What color are you going with ?

    What color are you going with ?

    What color are you going with ?

    :):):):):):):):):):):):):)
     
  23. Bob K
    Joined: Mar 3, 2001
    Posts: 5,772

    Bob K
    Member Emeritus
    from Antigo Wi.

    To those that asked about the color, it will be the same color, I don't want to spend the money that the Divorce would cost me. Maggie would be pissed if I changed it and frankely I love the green with the tan top.

    Eric, Maggie read your comment about yellow and orange, she says to tell you to get bent!!!!!. Seriously see the above and most of the comments about the current color. Excluding you and 3W larry of course.

    Mikey, yep that is the guy that did the finish work on the car 5 years ago, he is great, I am damn lucky to have found him.

    Yeah guy's, even if that car don't make it, we will for sure. The 62 is ready to go just in case.

    Steve, we did that plastic when we cleaned and repainted the shop this winter, I think it took us about 2 hours, we did have the benefit of some staging that I borrowed from a friend, that made it go a lot faste, we left it up because of the over spray and dust that this project is gonna create.

    Hey John, we will be happy to be your tour guide, see ya this weekend.

    Thanks for all of the words of encouragement guy's.

    B:DB
     
  24. 1950ChevySuburban
    Joined: Dec 20, 2006
    Posts: 6,185

    1950ChevySuburban
    Member Emeritus
    from Tucson AZ

    Glad you're staying with the same colour. If anyone can get it done, you can, Bob!
     
  25. touchdowntodd
    Joined: Jan 15, 2005
    Posts: 4,069

    touchdowntodd
    Member

    santa, get your elfs in the shop!!! they'll have it done tonight!
     
  26. ...doc...
    Joined: Feb 18, 2007
    Posts: 755

    ...doc...
    Member
    from Houston

    damn, all I see are little red X's
     
  27. Nick32vic
    Joined: Jul 17, 2003
    Posts: 3,064

    Nick32vic
    Member

    We'll see you in Austin.
     
  28. 57JoeFoMoPar
    Joined: Sep 14, 2004
    Posts: 6,511

    57JoeFoMoPar
    Member

    You'll make it! If it wasn't for the last minute, nothing would get done!
     
  29. Ooops, I hope there weren't any beer rings on the front valance!

    This makes me think of all the cars we read about that were iconic in their day and then redone/fixed/changed as the miles added up. Credit to you for all the miles AND for keeping it up when needed.
     
  30. Alex Yohnk
    Joined: Sep 7, 2005
    Posts: 826

    Alex Yohnk

    The work might be done, but how long does it take to get outta that garage?????? I think it took me a week just to WALK through Bob's shop!!!!!!!!!!
     

Share This Page

Register now to get rid of these ads!

Archive

Copyright © 1995-2021 The Jalopy Journal: Steal our stuff, we'll kick your teeth in. Terms of Service. Privacy Policy.

Atomic Industry
Forum software by XenForo™ ©2010-2014 XenForo Ltd.