Register now to get rid of these ads!

Finally scored a 54'

Discussion in 'The Hokey Ass Message Board' started by Easyspeed, Apr 6, 2013.

  1. Easyspeed
    Joined: Aug 3, 2012
    Posts: 60

    Easyspeed
    Member
    from USA

    I've been searching high n low for a solid project. Finally, brought it home today. It's a 54' 2 door hardtop bel air. :D
    Runs n drives, kinda cool already but I'm planning on some changes over time. I'm no pro wrench, but have built a few motorcycles, worked on some cars, and work as a machine builder and fabricator. (not the same as auto, but hopefully it will help)Ha!

    The 54's had some body work done, it still needs lower door patch ( in and out) Where can I find these and any other sites for panels and parts? The cars is close to all there from what I can see. Trim and a few bits are in the trunk. I'm pumped, I want to do a resto mod sort of car.. I guess. No plans on chopping it, just going with a minimal amount of exterior trim if any will be used at all. Cleaning up the body, shaving the door handles, filling trim clip holes, antenna etc... Did I mention the bumpers are new and the glass is all good!

    Although the 235 runs good, I sprung a major leak at the interstate on the way home. I wasn't pushing it to hard, but I'm sure the 60 year old 235 and power glide didn't want anything to do with the interstate. I was running 60 or 65 mph tops for about 45 minutes then the leak caused some smoke.I pulled over and at idle the car began to pour oil from the rear of the engine. I shut it down immediately, called a flatbed for the rest of the cruise home. After we got it home I check to see if there was any oil left in it. It was still dam near full. Only guess I have would be the breather is clogged and the pressure blew the seal, especially if it was overful. When I checked the oil looking at the car pre purchase, I noticed it was a bit over, but it didn't seem to cause alarm.
    Enough of this saga. time for work.

    Here is a photo with a filter to make it look cooler than it actually is...;)

    [​IMG]
     
  2. ChopTopJimmy
    Joined: Mar 14, 2007
    Posts: 1,451

    ChopTopJimmy
    Member

    Congrats. Nice start to a kool project. Have fun with it. CTJ
     
  3. Easyspeed
    Joined: Aug 3, 2012
    Posts: 60

    Easyspeed
    Member
    from USA

    a few better pics:

    [​IMG]

    [​IMG]

    [​IMG]
     
  4. Congratulations,the car looks nice and shouldn't take too much to make a it the way you want,,keep us up to date. HRP
     
  5. mbrede
    Joined: Aug 7, 2008
    Posts: 60

    mbrede
    Member
    from Minnesota

  6. 30modelacoupe
    Joined: Nov 1, 2006
    Posts: 359

    30modelacoupe
    Member

    Damn!!! I love it.
     
  7. KenCrete
    Joined: Jun 1, 2012
    Posts: 157

    KenCrete
    Member
    from Milwaukee

  8. brady1929
    Joined: Sep 30, 2006
    Posts: 9,472

    brady1929
    Member

  9. sweeden
    Joined: Mar 25, 2013
    Posts: 164

    sweeden
    BANNED

  10. Dave Rondou
    Joined: May 26, 2008
    Posts: 669

    Dave Rondou
    Member

    Nice score. Love those hardtops.
     
  11. flamed58
    Joined: Feb 25, 2007
    Posts: 226

    flamed58
    Member

    kool project Dusty
     
  12. milanperformancecycle
    Joined: Apr 22, 2012
    Posts: 18

    milanperformancecycle
    Member
    from milan t.n.

    Cool car man. Love the wheels. Good luck.


    Posted using the Full Custom H.A.M.B. App!
     
  13. 5559
    Joined: Oct 25, 2012
    Posts: 362

    5559
    Member
    from tn

  14. Finnrodder
    Joined: Oct 18, 2009
    Posts: 2,970

    Finnrodder
    Member
    from Finland

    Looks good,that shovelhead doesnt look bad either
     

Share This Page

Register now to get rid of these ads!

Archive

Copyright © 1995-2021 The Jalopy Journal: Steal our stuff, we'll kick your teeth in. Terms of Service. Privacy Policy.

Atomic Industry
Forum software by XenForo™ ©2010-2014 XenForo Ltd.