The Jalopy Journal
I have a 50 f1 out of my truck that I can measure let use know what measurement you need.
If you could put a tube in the frame the size of the bolt to prevent frame from crushing that would be great. assuming a boxed frame area. ED ke6bnl
the more people the better I was fortunate to have it outside with a gantry and air condition compressor lift. [IMG]
we had the same problems and sold two of them on ebay as is with an explanation of the failure and some lucky lover of mallary bought them and we...
the http://www.metalshield.com/ looks like it would be a great replacement for lizzard skin. made just for our purpose. I am thinking seriously...
some more if you dont mind [IMG] [IMG] [IMG]
some more pictures [IMG] [IMG] [IMG] [IMG]
some more BBQ pictures [IMG] [IMG] [IMG] [IMG]
Thanks Ray for putting up with us and the great BBQ food. here are some more pictures more car came as I was leaving though; [IMG] [IMG]...
I got one of those videos also and I keep getting mail about buying it or returning it and I never asked for it I have yet to watch it (but will...
I believe that is what the manual said to do BUT on a 6cyl. I had to divide it in 1/3 and that seemed more unreliable. Thats when I went to the...
tell me what you think, I have done it and it seemed to work, I was told by and old mechanic this one. I took an old dist. cap and cut the center...
I will plan on going to the BBQ I live close by in Agua Dulce, Ca. I can bring a 12x12 pop up and ice from work let me know if that helps....
WOW that is what I keep telling my wife these people who buy a electric gas car don't have anything on us who keep an old car running. Can you...
[IMG] [IMG] Well not as cool as some of your guys my first ever. made from trailer hitch reciever material, may be over kill. Ed ke6bnl ye...
an Old Mustang parts supplier catalog did a test with the intake fastened to a table and was able to get over 5000lbs pull b4 the plate distorted...
or you park in a non parking space as long as possible till the police come by and chase you out. And you do the same thing all over again. ED
Here in California what I had to do is have an officer verify that I was moving the vin from the engine to the existing one on the door jam. even...
Not sure about the car BUT my 53 chevy truck the vin was the number on the motor. So when I got the truck no motor had to have the vin ided off...
AT this time you may want to check the fuel volume and fuel pressure. Sounds like a restricted filter. Ed ke6bnl
l I was thinking this would be good to make bends in tubing then heat it up to liquifiy it and remove it. Ed ke6bnl
I have sand blasted 2 windshields successfully only to break them when I sand them I would guess if you new someone that had a water jet they...
and what about price I got an 85 s10 longbend and 85 s10 blazer both for $400. wont have into this project as much as I would have to pay for the...
Thats the project I am working on 53 chevy AD 3100 on an 1985 S10 longbed frame with the rear axle out of a 1985 s10 blazer but am too cheap to go...
My girl worked at a trans shop and when her jeep cherokee hydraulic clutch went out in the trans they fixed it for parts. As an experiment we went...
Planning on being there Sat. early only about 70 mile drive from Agua Dulce. Ca. will try to stop by. Ed and Son James
Thats looking good I kinda went in the same direction mine is all 50 F1 though. Got lower then I want after it all settled in. I will have to go...
Here is mine still a long way to go. [IMG] and here is another shot [IMG] and welden up the fire wall holes before it is too late...
If you have a lot of money the corvette catalogs show an already set up system with the filler with the pcv valve and I believe the fresh air in...
Separate names with a comma.
The Jalopy Journal
