The Jalopy Journal
4" will do the 600's, believe that was the standard issue, talking wide 5 here but after that also. Any 16" wires I have acumulated I had to cut...
The mixture dash is not "rare" but a hard to collect the components. http://www.directimagehost.com/is.php?i=75622&img=Dsc02165.jpg Also the...
I understand the stamped steel wouldn't accomodate the 12" clutch, need to use the 11" with them. Haven't had reason to mock it up yet, can't be...
If it's a half ton, three speed trans, it's worth the wad no sweat.
Honey Brown makes a root beer colored aluminum bottle, excellent, no rusty sledge.
Mine is a 6000 AC tach., may be oddball but: one was 12V+ , put it to ignition switched side. one marked - or ground. I put a ground loop in my...
I think the term is "floor truss", but essentially they are a beam made of top and bottom plates with webbing between, plywood added to the sides...
...and you have to want it really really really bad.
There is a "double D" style hole in ethe later, stationary anchor type shoe. Take a piece similar to the cam, but just a spacer for the wear...
I haven't seen any yet and have had a Canadian 8RT pickup motor and seen a bunch of flatty truck motors. Rare in these parts as far as I know, and...
37 driveline with 3:78 and 700 16. 2000 at 50 mph, I usually stay below that, sometimes hit 55 on a state highway, 2150 rpm. Any direct high...
DIY, they aren't that tough and by the time it's assembled you will know exactly what's involved in adjustment. That's manual steering, I have...
Yeah, nickel would be the proper, as I have some around I use rarely for cast repair. When I can get away with it I braze cast, can see the bond...
Put it under, and the gauge from the dash fitted next to the filler. http://www.directimagehost.com/is.php?i=102087&img=DSC02460.JPG
In the same boat, love the oddballs no one is going to re-make, so I scoff every crusty mess I can. Just got a 39 frontend for 5 bucks at auction...
Link to some pics of my project. I used about '37 axles, like the motor /trans., my front look's like the axle you have. The '46 will have quite a...
FYI the detroit diesels ID is the cylinder number and cubes. There was never a 5 cylinder I know of. They started with a 2-71, usually a power...
http://www.directimagehost.com/is.php?i=136739&img=P9130004.JPG http://www.directimagehost.com/is.php?i=132082&img=DSC03516.JPG
Howdy from WNY, Wife go's down to that area on business, lot of skiers and sledders come here at snow time. You probably heard but just in case,...
The square one was not enough. So I found a K&N one by dimensions and made a bottom and sprayed it with bedliner, hammered a top, form a gasket to...
I have complete rears, one is 48" on center, the other 3 I believe are 46". The housings I have that are loose measure 22" from center to flange,...
I mounted mine outside. I knew the negatives, but I did it anyway because that's what I wanted. All the "roll" flex has to come from the frontend...
I don't get them very well stored. I put the shop vac down the intake and exhaust ports, (take off the ex mans. and carb) when I pull the plugs to...
I have the 21 stud and a guy from Ohio modified one tofit the stock end-frame, original gen pulley screws right on. Tround a hundered bucks...
Straight cut gears, says T59..... something on the side, has plates for PTO install on sides? Heavy truck, I have a few, weigh twice as much as...
Too bad more don't share their auction info on here. This auctioneer is one I watch although operational territory is out of my range, somebody...
The NAPA wheel cylinder replacement numbers are F8265 right front and F8264 for left front. I assume the same for the rear, just opposite sides,...
I happen to have some combos laying around so hgere is some brain food.. First pic in the foreground is the front 17" x 550 goodyear and 16" x...
I compensated for the shortening of the frame by doing the front "Z" (pie cut) by making a "S" bend piece to reach back to the rear crossmember.A...
Separate names with a comma.
The Jalopy Journal
