The Jalopy Journal
Its from a early aluminum glide coarse spline. I think they were 10 spline. This was a mid length extension housing unit. 9" housing length.
I'm looking for a 10 spline / 1350 u-joint slip yoke for a powerglide. Anyone have a idea where I might find one? I've tried Strange/Moser/MW. I'm...
C4B in good shape. 150.00 + ship. Early corvette factory intake? Snowflake emblem. 3704129. Needs some repair at water ports. 150.00
Just found this thread. Excellent craftsmanship! Hope you have the nova clip soon. I'd like to do a dropped tube setup in my 64.
1968 M20 Muncie four speed, Lakewood scattershield with block plate, MrGasket vertigate shifter, Hays b&b pressure plate with puck disc. 1400.00...
1960 tudor sedan. All original. 144 six std. Runs and drives. Floor pans need replacing and clutch chatters. Good window channels, rockers and...
Nice Work! Wish it was mine.
Thanks for the tip! I did grind a flat on the head bolt and the rocker bolt. So far its working great.
Well pulled the number six plug and headbolt. Ran the engine until all the crud came out of the oil passage. This did work! Rockers are oiling...
Yeah its a standard. Thanks for the info. I have a local salvage yard that has lots of Ford sixes. I'll have to go out and see what he has. What...
I think I need a five bolt bell housing 200 if I swap. Having upgraded carb/dist and other parts would be nice. I've worked on a Holley like the...
This one might be a smoker too. Don't know yet. :)
That might just work. With the bolt out and no compression in the cylinder the oil pressure would push out the crud in the oil galley.
Ok, I got it on the wheel well. I put it on the lift today. Now I found a bunch more stuff to do.
I just did rough measurements. Guess I better check it closer. It is the stock axle. Did you just have to roll the fender lip, or is more required?
I'm thinking about smoothie steel wheels. 15x7 with a 4" backspace and 205/50 15 tires. It looks like they should fit. The previous owner called...
Nice Falcon! What wheels do you have on it? 15"?
Thanks again! My engine has the bottom half of the system. There is a oil line and a petcock to adjust the amount of oil going to the rockers. So...
Thanks! I tried the air but didn't use a rubber tipped gun. I'll try it again tomorrow.
Howdy Guys, I just bought a 60 Falcon with the 144 six. I got it running today but, the rockers aren't getting oil. I tried the head bolt, grind a...
Thanks for all the help. I've found a few sources for parts. Time to get it done. Mark
I got the pic to work.
It just has bottom pan. Main case is cast iron. This was a working unit. It's been sitting for a very long time. Thanks for the help. If I get...
I'm going to rebuild this tranamission for a friend. The car is a 56 olds 88. It does have a park position on the selector. I want to make sure...
Pull the top off. You have a float needle seat that is loose. Just tighten it up and your good. Had this same prob way back when.
I have a set of those too. Mine use a beveled washer. Hope that helps. If you know where to find them, I'd like to know.
[IMG] [IMG] [IMG] [IMG] This is my new project. I call it Texas Outhouse because thats what the rodents and racoons used it for.:eek: It was...
Welcome to the site.
Howdy, My first post. Been looking here for a while. I've been into cars since I was old enough to know what they are.[I'm 54 now.:D]. When I was...
Separate names with a comma.
The Jalopy Journal
