The Jalopy Journal
If you dont have a lockup converter (elec wire connector on trans) then theres no reason to suspect the converter by just changing the carb,...
Found my answer on Holley's web site; FUEL REQUIREMENTS Typically, at wide open throttle, full power, an engine requires 0.5 lbs. of fuel per...
Im building 6/71 supercharged stock sbc 350, it'll have two 600 holley 1850s w referenced power valves, my question is can I use a mechanical...
1970 Schwinn world traveler
I got mine from these guys, nice radiator, you can paint em black if you dont like the bright alum....
Ouch, thats ugly
Im a long long way of turning the key, car still looks like my avatar and I havent even started on the frame yet-its too dang cold out, so im...
"Now its time to put this huffer back together.Before we go any further I should mention that a blower could be accidentally put together...
OK I need to put the brakes on for a second, I just realized my gears are on the back of my blower and none on the front! has a funny back cover...
I thought all the small bore's were 6V71's and large bore were 6-71's edit- upon further investigation the 6-71 can be ether. one way to...
Im thinking I may go with the 39 top and 35 bottom for a 10.2 under just to stay on the safer side.
My 70 350 sbc is rated at 255hp, your engine was probably about the same as a natty, how much increase in HP or total HP do you think you made if...
Would it be better to go a tooth or two down? if I went to 39 top and 35 bottom that would bring me to 10.2 underdrive. and if I went 38 top and...
I picked up a 671 GMC blower and need to know the best pulley tooth count, It will sit on top of a stock 350 chev 1970 truck 4 bolt block and 441...
I just ordered a set of Carrara chrome rear coil-overs for the 31 :D
Free Shipping at Speedway thru 12/1. Just thought Id throw that out there for any body that Uses Speedway for parts. Iv'e spent a lot of coin...
I just picked up a 671 myself :) I got the CD from Deans blowers and it tells you step by step how to convert it over, tells you how to clearance...
Haha! thats funny, might be a bit gritty though!
Nice, that would be the cats ass for big stuff!
Nice and simple, I think I'll go this route, thanx for the Idea :)
I used a suction system for years and it is the slowest waste of time I've ever spent, I built a low/high pressure pot system Designed by...
ONE BIG MENTION HERE IS DO NOT USE PLAY SAND OR REGULAR SAND YOU FIND AT MENARDS OR FARM N FLEET STORE, THAT STUFF IS VERY HAZARDOUS THAT STUFF...
Yup its gettin cold up here in Minnesota, I wont be painting the car till next summer, just doing the tin work over the winter, as far as the rust...
Triggerman, I do want to use a metalic color, so should I use lacquer or something else? I think I'll built a car port out of 2x4s and a tarp but...
Its the Platinum model 3015, he said he had about $400 into it after getting the smaller 1.3 tip. didn't com with the regulator or aluminum cup...
Well after doing some research as well as your input I opted for the Sharp, the fellow is a professional auto painter, said he has a lot more into...
I should also note that the paint will be done in the driveway.
I always thought the laquer paint was good foe screw ups, thats why i wanted to go that way, being a novice I know Im gonna get some run or flat...
I'm not picturing what you mean? are you saying they used the flat stock for the outer frame and 3/8 rod for the vertical fins?
I have I nice big 80 gal 2 stage compressor, there is no paint on the car (see avatar) its basically covers with rust. I'll invest in a spray gun,...
Separate names with a comma.
The Jalopy Journal
