The Jalopy Journal
There are different lenght modulator pins for the later c4 but you can convert to an adjustable modulator instead of changing pin lenghts and it...
Okay, Some of these responses are accurate, but the most obvious cause for this problem has not been posted yet. How long has it been since you...
- Boot camp Great Lakes- Sept - Nov '89 - GSM "A" school Great Lakes Dec '89 to Aug '90 - USS Vandegrift FFG-48 Aug '90 to '92...
Snake9t9 #500
Not exactly an answer to your questions, but I hope the flex plate not only will fit your bell housing, but also that it is for a 28 oz. imbalance...
Can't name just one, but i've got a fav list. #1 1964 Ford Thunderbolt #2 1932 Ford 5w coupe #3 1940 Ford pickup #4 1954 Chevy Bel Air
Piss off the enviro nazis.....Call it the "Greenhouse Gasser!"
Intake won't cross over, The 351 has a taller deck than the 302. The timing cover will bolt on but ford used three different timing marks so it...
I think the one exception to this rule is the sbf GT40P heads. But I don't know if they will work on a 2.3.
I have not posted to the board in years. I mostly just stop in now and again to check out what is going on, but this post promted me to reply....
I had a similar problem with mine and it turned out that the sub rails and cross channels were out of square. If the frame measures out square and...
I could probably get more pics of it if ya wanted. The guy that owns it lives a couple of miles from me. I stopped by his place the other day to...
Ahhh, I see. Must be a real fine line there though.
How does one get a wreckless driving ticket for anything done on private propertly (parking lot). I could see a vandalism citation but no way the...
Try this link for interesting info on oil filter construction and filter media. http://people.msoe.edu/~yoderw/oilfilterstudy/oilfilterstudy.html
I would think the spring rate would be very high for the back of a model "A" or '32. Do you plan to remove some leafs from the pack?
My understanding of this is that Ford was actually the founder of Cadillac in a round about way. He had started a car company and wanted to build...
You may have problems with U-joint failure or vibration if the cancelled angle between the rear end and the tranny is not right around 3 deg. Why...
How about Donovan (sp?)....?
"Made my Pants tighter"... No kidding! This car is so close to what I have had in mind for my own coupe! I'm planning on running a wider 10...
Kids are Great! My little 2 1/2 year old daughter comes out to the Garage, points at my "A" coupe and says "BROKEN!", "Daddy fixing ???". Makes me...
Excellent Tech post. I feel as though I've been to "Skirt buildin' school" haha. Very nice. Thank you!
If so, I have a few Q's on the build. Thanks - Duane
You very well may have won if your reaction time was better than his by enough to offset the E.T. difference. "HOLE SHOT!!!" :)
There are a couple of ways to go about it for the fuel tank. One popular way is to add one behind the seat, at the front of the trunk area. You...
Sorry, but I couldn't dissagree more! If this were 100% true these Arabic nations would rise up and take a firm hand to those who taint the middle...
I've got a set of purple hornies with the header flange on one end, and the exhaust flow is against the "ramp" side of the louvers.
How about using a two piece tunnel ram, minus the top. You could then fab a sheet metal top to run whatever set up you would like.
A world class T-5 out of a mustang should be a bolt up if you can find a bellhousing out of an SVO mustang or turbo coupe Thunderbird. As far as...
Easy off oven cleaner.... and forget the bead blast. Just make sure you rise with LOTS of water. The oven cleaner is caustic.
Separate names with a comma.
The Jalopy Journal
