The Jalopy Journal
I am going to pull my SBC enigine out to fix some small items, and to replace the tranny, and I am kinda in limbo on what if anything to do with...
How much is too much for the street? I'm having a new glide built and my cam card calls for a 3000 stall converter, and I know that higher stalls...
I had to switch a leaking master cylinder on my car with a remaned one. 67 drum/drum with 46 Ford brakes front and 57 chevy rear 10lb residual...
I just added a new sender to my 1936 Ford tank, and with the ign on and the lever of the sender at the top, or full; it reads full on my SW gas...
What would cause the plastic of the push in type fuse and some of the holder to melt? My electric fan was not working and when I checked the...
I am trying to fine tune my 350, that is 030 10:1 comp with an edelbrock C3B intake, and holley 600 vac sec,plus GM single point dist. It...
With a cam, with a duration at about 282, (I can't find my card) and lift at 480, what type of vaccum should I see at idle? I'm trying to tune...
Anyone use this stuff? Would it be better than D/M for a rebuilt powerglide, that was built awhile back but not used until recently?
Is it recommended to run a tranny cooler in addtion to the cooler built into the bottom of my radiator? It is a stock 36 rad that has been re...
Anyone running lap belts in their rumble seat? I imagine it would not be hard to add them, but I would like to know if anyone has done this....
I have a set of chrome smoothies #64 from wheel vintiques and another set of their baby moon hubcaps recommended to go with the rims. #1011...
I am in the process of rebuilding my 4160 600 CFM manual choke 1850-2 carb, and I noticed that there was a small filter inside the inlet. When i...
2007 Cavalcade of Cars this weekend at the Agri-Center at the Hamburg fairgrounds. See attachement regarding the pinstipers convention. 100%...
Does anyone know what baclancers have the timing marks at what locations? I currently have one on my 350 with the mark at 12 or 1 at TDC and...
What would happen if you had a one wire alt and wired it like a three wire. I "ordered" a three wire alt from moon awhile back and wired it...
Found a crack on an otherwise excellent exhaust manifold. It is in the collector part; front, where the two ports come together. Should it...
I picked a pair of finned Cal Custom V/C's up. One has a hole in it already that I plan on using for a PCV. The other is uncut and unmolested....
I'm having some issues when my car is running, it drains the battery. When it is running I get a reading of -60 amps on my ammeter. after I...
I'm trying to get my engine running correctly, and I could use some tips on tuning. It is a 350 SBC with a 600 Holley. It is running rough...
I have to take the valve body out of my tranny to get it rebuilt. Right now it is a manual shift, in a powerglide. I can get a standard one...
June 16th through July 8th at the Amherst Museum 3753 Tonawanda Creek Rd Amherst NY 14228 If you are in the area stop down, one of the guys...
This Sunday at the Rosegarden reaturant at 2753 Wehrel off of Transit. 7-4 We had 140 vendors last year Auto parts only, be there or be square,
How much travel is there about 12 inches from the pivot ball of a wishbone? With a 38 ford front end, stock axle/wishbone, reversed eye posies...
How many folks have 35-36 Fords built, in the works, or... Let's see em. Here is mine.
Not quite finished, but put together for our club display at the Hamburg NY Cavalcade of Cars.
Do you have to remove the stock cradle to mount a 350 in a 36 Ford? I have a poweglide in now and it fits well, but I can get a cheap turbo...
Cavalcade of Cars is this Friday, Sat and Sun at the Agri-Center in the Hamburg Fairgrounds. March 3rd, 4th and 5th If you are in town and are...
Finally got the motor running, my next question is how long does it take for a new tranny, with a ,probably, empty torque converter to build...
Had my motor running, then it stopped. When I went to restart it cranked until the battery worn down. Charged the battery, and all I get from...
I have a 79 350 with the crappy chrome oil pan, yea guess what it leaks. I have a brand new one piece fel pro gasket, and I have an oil leak at...
Separate names with a comma.
The Jalopy Journal
