The Jalopy Journal
Posting to see if anyone has a part number or has ideas for a "modern" ignition switch (Off, assessory, start) that will fit in a stock Model A...
I'm thinking of running cloth covered suppression core spark plug wires with a Petronix unit in crab dizzy. The one set of cloth covered wires...
Set of aftermarket brake drums for '42-'48 or hubs that sit the hub OUTSIDE of the drum. These were sold by places like Joblot, etc. and where...
Can someone tell me it Jim Gordon's Early Ford Parts in Rosemead, CA is still open? I've been calling for about a week at all different times of...
Does anyone know of a place in NJ that does vibratory tumbling for manifolds like in this video? Thanks, [MEDIA]
Curious if there is a need to replace the original/stock female spade clip receiver/pigtail/socket inside of Guide/BLC headlamps when converting...
Free + postage: 11" Ford truck pressure. Will need to be resurfaced. Picts to your phone, but it looks like a used pressure plate should. Will fit...
Need to paint my headers. I know a bunch of guys have used VHT for years. After reading the directions, they recommend a primer coat and then...
Original Hollywood D52 lisc lamp. Some very minor pitting, but very cool and should clean up nicely with some Evapo-Rust. Asking $65 shipped in...
Either old aftermarket or extremely well done original '28/'29 stanchions. Chrome looks much better in person. Total length is 15 1/4" and 10"...
'32 Ford cast aluminum "S" bend lower radiator hose connections. Made by M.E.C. in Ohio. New, never used. Not sure if he is still making these....
Pair of '33/'34 anti-chatter or steady rods. One side of one of the threaded portions is worn where it rests in the block. Should not effect use...
Trying to figure out the best way to do up the brakes for my AV8. I have both '40 & later '46 style brakes. I'm tempted to get their front drums...
**I posted this over at Fordbarn as well. OK, I got the transmission assembled, double check tooth count, back lash, etc. Everything fits...
Stamped steel Mercury bell house for use with 10" clutch. Mates 8BA style motors to early transmissions. Getting harder to find. A little...
Hello All: I'm reaching out once again to the HAMB family. I'm on block #5 in my search for a good one. If anyone has a cleaned, checked, and...
Slightly used Weber 10.5" street/strip. It was used to drive a car down the driveway and back then taken out. It's has since been on the shelf for...
I believe in saying "thanks" when an acknowledgement is due. I needed to re-up my TRJ's subscription and also my Alliance membership is set to...
So, you learn something every day. After speaking to Ronnie Roadster, I learned that a '41-42 Merc block can't easily be converted to full-flow...
Stahl headers is sadly out of business. Looking for some recommendations where to get quality steel mandrel-bent J's, U's and straights to make...
Besides vintage military units, I've found that Crow and Simpson are making the old, military-style buckle seat belts. Anyone else know of a...
Are we having fun yet? OK, trying to set-up the pedals in my AV8 project. It's looking like '33/34's arms will work better in the '32 pedal box,...
Howdy: Looking for some help. I need some picts. of lakester-type exhaust (you know, the type that goes over the frame rails and dumps into a...
Zach Suhr is currently working on my AV8. We are at the point of needing to get the exhaust done. He is certainly more than capable of handling...
Putting my '39 trans back together. Have all NOS gears, bearings, shift forks and super nice top and case. Got a lot of the other parts from...
After years of having this project linger in various states of completion, @zachsuhr is working on getting my chassis set-up while I work on the...
Does anyone know of a manufacturer making a diaphragm-type clutch for flatheads using an OEM-style throw out bearing and 3 speed input shaft?...
I have three new old replacement stock inner distributor caps and rotors. There are all US-made with brass contacts. Selling each set for $30+...
Brand new set of Ross pistons for .125" over X 4" stroke. This makes a 276 c.i. I bought these new in 2008 and only opened the box and unwrapped...
Model A to '32 shell Rootlieb louvered two piece hood top. Only used for mock-up. Top does have flash rust, but the bottom does not. Has '32 style...
Separate names with a comma.
The Jalopy Journal
