The Jalopy Journal
Here's what's going on... The clutch fork is/was the pedal stop (the pedal arm goes down through the floor). When I was pressing on the pedal to...
I will pull the dust shield off when I find a helper to work the pedal. Thanks gents.
The way that it chattered going into third felt like the clutch disc was not disengaging enough. The pedal itself, once I was pressing on it, to...
I have a couple of problems with the Y block clutch pedal in the Model A. 1. On two occasions, I've tried to shift from first to third (T-150 3...
Well the newest update is that a few buddies spent a weekend getting the trans swapped in... We needed to swap bearing retainers (they seemed...
Sounds good. Thanks to all. Thanks for clearing that up, Rich. The only thing that's new is the overdrive circuit which is going through a relay.
There is no continuity between Gage and Coil on my switch when it's off. I currently have 3 things on each terminal...not even sure what they all...
So anything that needs switched power can run off the "coil" terminal... for example a relay that runs a solenoid for an overdrive? Thanks.
What's the difference between the "GAGE" and "COIL" terminals on the '39 Ford ignition switch? They both seem to get 12v with the ignition switch on.
Thanks for the tips. My "crutch caps" will be here tomorrow and I plan to use those...but now that I have it back together and bolted up there...
I will take a photo of what the trans side looks like later and post. I think the guy that rebuilt it has it plugged. It’s an oddball- AMC...
This is the threaded part of my speedometer on the back of the transmission...I am going to go with a GPS Speedo so I want to cap this off. It...
Ran into a snag...seemed to be going well but this new transmission didn't have the correct bellhousing bolt pattern...the OLD one had both, so I...
One more question...if I wanted to make sure that the bearing retainers are, in fact, the same and won't leak (after I replace the seal)...would I...
HMMMMN... I guess the HAMB stopped telling me when I have replies... Miker- I was just coming back to this thread to send it to you over on the...
Getting ready to replace (hope it fits) the Ford 3.03 in my Model A with an oddball AMC transmission (I have other posts on it) that is...
I was able to use a cutoff wheel to get about 3" or so out from behind it and it slid out nicely. I'll just cover it with a piece of aluminum, or...
Been UN-doing the puzzle to get the 3.03 out of my 1930 coupe and I got it all unbolted and went to slide it back but the Jeep topshifter is hung...
And everyone on this thread has one of those, "One time, this idiot on the HAMB...." stories! Actually, I don't feel so bad because other...
SUCCESS! Finally. Well...it's KIND OF FUNNY... This part showed up today from an AMC Supplier (Blaser's - in Illinois) and was guaranteed to...
Damn...I think a parts store in New Hartford told me that all the Fleet Prides except for Danbury stopped doing them. Good to know.
Yeah- I have the same luck. The problem is that this seemed like the easy option from the get go- fits exactly where my current tranny is and...
I tried FleetPride last year and was told that they're out of the driveshaft business, sadly. I may have had some headway today. One of the AMC...
snoc653...I THINK I have that one now...it's 1.5" seal/shaft diameter. My thought was to pull out the seal and see if the splines fit...the one I...
Well...I'm still defeated. I worked on finding this damn thing for 7 hours today and I am only MARGINALLY further along in that a couple of AMC...
I found this to be a good site...this is what I used to get the ones I just ordered. https://www.skfextranet.com/crsealsfinder/
Thanks Gimpy... That's what's so strange about Anthony's part number...all of the cross-references show what you posted, but our measurements are...
I have a dial caliper and, with the seal in place, got somewhere around 1.94"... I purchased 2 today- one is supposed to be 1.938 OD, the other...
I ran a triangular needle file along each spline just in case but that didn't help much. I thought about that, though. The seal that is...
Someone on the AMC forum posted this...these numbers didn't come up on Google but figured someone here (or in the future) might be able to make...
Separate names with a comma.
The Jalopy Journal
