The Jalopy Journal
I've had this for years, and honestly have never seen another. I'm not a cowboy but some of you guys in cattle country may recognize it.
Twenty years ago I gave this old book of mine to my son. I'd forgotten all about it until I found it while cleaning out his closet yesterday....
Click here: YouTube - 1930's Essex Terraplane Auto Ad
Click here: Moyer Made - Projects: 1/6th Scale Chevrolet V8
Click here: American Cars by Hans Tore Tangerud
[IMG] [IMG]
We were in a rest area on I-75 in North Georgia yesterday when I spotted an 18-wheeler headed south. The whole rig was white with a huge Cherry...
Anyone headed for Graceland? Or Tupelo, Mississippi Click here: WTOK Community Events
SBC, Vortec Heads, RPM Air-Gap, Edelbrock #1806, MSD Ready-To Run with Autolite 103's. Plugs 2, 4 & 6 are all a bit richer looking in person,...
I have to admit I wasn't, and actually feelng a little guilty. How about you guys? Shop time or shopping time? Merry Christmas HAMBERs.
Steering is on the wrong side. HaHa
Anybody besides me interested in a H.A.M.B. Zippo. If there's enough interest maybe Ryan or somebody could have a run of small cloisonne...
My machinist uses Purple Power to clean aluminum heads. Has anybody had any experience using it to clean aluminum wheels?
I gotta believe there's already been a thread on this, but I couldn't find it. If not, let's get those pix up.
I needed some of this earlier today. Click here: YouTube - Wynn's 'Start You Bastard' Engine Additive Advert
I've got a Edelbrock 1806 on a SBC that is presently calibrated in the number 8 position on the Calibration Reference Chart. That is 2 stages...
So how do you guys keep your engine operating temp at about 185F in the fall/winter months, especially with a heater? I have two (3) different...
Looking for the following; 5/8"-18 X 2-3/4" Button Heads (stainless) 5/8"-11 or 18 X 6" Button Heads (stainless) Neither Gardner-Wescott,...
Trying to replace the spring perches in a chrome '32 ford dropped tube axle with new adjustable ones............if possible. Working on the...
I need 1/4" cut off each of the bars on my front stainless 4-bar set-up. My machinist says he thinks he can do it without marring the bars by...
Does anybody have a trick way (without welding) to attach hard brakelines to a smooth Ford 9" for a short distance (from the drum backing plates...
Can anyone give me the recommended torque for the spring clamp bolts??
My Model A (2-dr sedan) has a pair of coil-over shocks in the back, hooked to a TCI '32 frame, parallel 4-bar and Ford 9". THE PROBLEM IS THE...
I've got a Model A sedan on a TCI '32 frame, mono-leaf spring front, coilover rear. It sits about 1/4" low on driver's side front (spring...
What kind of mufflers sound the best with scavenger pipes?
Is this good advice? Instead of removing the third member to change diff lube, remove the bottom stud and replace it with a bolt? Then whenever...
I bought this album new in 1961 (the year it was released). I still have it in near-mint condition. Song Titles [IMG] Hot Rod Lincoln [IMG]...
Does anybody know the part numbers (Felpro or other) for the inner and outer axle shaft flange gaskets that go on a Ford 9" (Big Ford - New...
HAMBERs, I'm looking for a air cleaner element like the one in the attached picture, 14" diameter, "round hole" design, black moulding. The...
Are there any SBC inside the chassis headers besides the block huggers that will clear the Vega steering on a '32 Ford? How about full...
Separate names with a comma.
The Jalopy Journal
