The Jalopy Journal
Hi,Do you want to buy the mags or just a scan of the add? glider.
Farmcal, In my future projects pile is my"duke" 1980 jeep 4 cyl.GM motor has chev.V-8 bellhousing pattern on block,flywheel is different...
Kustom 7777, Run the flat motor! Only fitting mill for your KOOL Merc. A snap of my f/h engine test stand. glider.
Prewar 24 stud 239" My pride and joy.:D
My attempt at an early lakes car,hope to eventually have"banger"power.Narrowed 26 touring front,early ford axles/brakes,powerglide,265" chev w/2x2...
Quick I.D. between 54 and 55 ci.glides,54 had closed driveshaft and 55 open driveshaft,correct?:eek: glider.
Yup, like GTO said mine measures 70" long and It came out of my buddy's 40 2 door. glider.
got one in the shop,will measure it tomorrow glider
H/R, Tried Pertronics/points swap and it will NOT work.Pertronics mount plate is to long,it overlaps the vac. advance connection and the point...
Jim, Make sure the front balancer has not SLIPPED:eek: ! Meaning the outer ring in relation to the inner one.The rubber bonding between them...
H/R, I have a Pertronics conversion in a vette dist.I just bought.The module is #22V-V4 and the mount plate is#1182d.If memory serves the early...
I mfd. a "short" GM trans mount for an aluminum glide as follows,cut a section of 1/4"x2" flat as long as the top of stock mt.,drilled the...
In the summer of 1965 a local guy bought a new Chev. Impala convert.,factory 425 hp.396,4 speed and 4:11 posi.we drove to Casper Wyo.drags and he...
And late model 27 doors have a different inside latch assembly,more like"A" open car latches.The late doors fit right on my 26 modified however.:D...
If it is all nicely steam cleaned/washed, it will have water inside it! Combustion chambers,oil pan,everywhere.Nothing quite like the feeling of...
GREAT!!! Another alive 265,and I thought I was the only one "lost in the past".Will be interesting to see manifold selection.The only thing I am...
C/56, What cylinder heads are you running? Stock 265" heads,even power packs have very small intake ports and the size difference in the...
Morning, I would check the following on an early flat motor. 1-- Is there anti-freeze in the cooling system?If it is and not in the oil pan that...
Kustchops,Stamped near the outer O.D. of the ring gear the side that bolts to carrier, will be some numbers like 9 37,this is the pinion teeth and...
Ken, WOW!,what a trip down memory lane.My first"running"hot rod was a 1933 p-up,looked a lot like your's.Circa 1961/62. Running a stock 59-A...
Great trip down memory lane,ran a 331 Cad in my '47 Ford more door in 1964.Made it from S.D. to Colo. 3 or 4 times.Not bad for a high school...
Any one have a good shop in Denver/Greeley/Ft. Collins area to get my T roadster de-rusted? thanks,glider.:confused:
I made one years ago,used a 55 chev.axle,2, 265 front pulleys for the slide hammer and welded on a spider gear to keep it all together.Knocked out...
My crack free 59-L block,.060 over w/factory relief.Some of us never learn.:confused:
Ryan I live fairly close to Northglen,27 miles,I am going to town Sat.so a look would be no problem. E-mail details.Have digital eqpt.also.:)...
Comet, Snap of my"poor boy"Nickson 2x2 for a chev. glider.
HRP, A thought,40 rear bones measure about 3/32" thick,while the 40 front bones are 5/32" thick.I cut rear ends off 40 rears and slid em into 40...
Greasel, Replace the syncronizer clutch,It's the large drum the 2/3 shift fork fits on.If the brass rings are loose in the ends, this = grind,...
Rusty, I think "Speedway Motors" in Neb.sells wire and fuel lines like that.We called em"see your fire wires",from an Honest Charley ad....
Wow, My first car was a 31 chev coupe with the top hacksawed off,no I didn't do it,this was in 1958.Think I paid 15$ for it,all I have left are...
Separate names with a comma.
The Jalopy Journal
