The Jalopy Journal
i bet the lincoln and eastwood welders are made by century.. century is owned by lincoln.. adding this, a friend of mine acquired a clarke...
its starting to weigh quite a bit.. when i finish up the bracing and add the legs it's going to weigh a ton probably.. i need to figure out how...
heres a post i started on my sheetmetal brake build http://www.jalopyjournal.com/forum/showthread.php?t=528979
on my T (street car) i'm using radius rods.. i set the engine/trans at 1 1/2 down.. set rearend 1 1/2 up... on the cars and trucks i've set up...
i downloaded this diagram here.. dont remember who the original poster was.. this is about the best diagram i've seen of different rearend setups..
i started building a sheetmetal brake 3 days ago. i used the plans from my site somewhat and added to them as i went.. i also made the clamp...
probably not what your looking for but i bought a cheap buffalo horizontal saw like 8 yrs ago.. for like $200... it stands up and locks into the...
i got a set of aldan eagles for $200 off ebay.
dont use acetone either.. believe it has tolulene in it.. for that matter dont drink diet cokes, do some research on whats in that stuff you'll be...
i bought a 90degree pneumatic grinder at harbor freight, also bought a bluepoint 90 degree pneumatic grinder at about the same time (couple weeks...
i hope you dont call that a guy!
i did a 90 mustang years ago. seems like i used 6x6x.187 plates welded to the floor... on the main hoop i actually cut the floor pans in the rear...
the takacs bender will do round tubing, chromoly or dom from 3/4 to 2inches it uses the pro-tools dies.. you also get a 30% discount on one die if...
thieves retag cars in every state, including kentucky.
yep twisted minis bender is made from the takacs cycle bender... he sells them on the ebay also..
heres a link i found to a message thread in a 4x4 forum, many have built the takacs cycle bender, many pictures of it in action.. i read in that...
the best plans i've found so far are from takacs cycles... http://www.gottrikes.com/Tube_Bender.htm you have to buy them but the plans are...
try some van sickle tractor chassis paint..
135 amp lincoln or miller can handle 3/16 thick.. just grind and bevel/chamfer and clean all the joints very good.. put the welder on a...
be patient, i probably wouldnt buy an engine from an individual, more times than not, an engine bought from an individual is being sold for a...
i'm running a lincoln 180c 220v machine.. its small, dont weigh alot, and welds great.. i got it from indiana oxygen 2 yrs ago for $750 with a...
the pictures of the #4 cylinder that were taken from the crank side looked like there was a nasty crack in the cylinder.. i have also read...
my 94 camaro has the peels... i'm going to scuff,wetsand, blend with color and reclear the panels.
going in my T
anyone know a place where i can buy 15 inch shells in 8inch and 4inch widths.. the 8inch wide shells are no problem, cant locate any 4inch wide...
wouldnt matter if the car is liscensed as a vintage anways.. it would be excluded/grandfathered out of that law anyways...
and also to run a virus scan, you boot up in safe mode, with no internet connection.. and also run microsoft's malicous software removal tool..
i know the op stated he wanted to take it to other peoples garages.. is this for work to make money? or a buddies garage to help him with welding...
third for moser
friend of mine had the same thing happen to him... he sold an old 60's chevy truck on ebay, guy paid for it through paypal at the end of the...
Separate names with a comma.
The Jalopy Journal
