The Jalopy Journal
You have the basics for a good rebuild. The new Edelbrock E-street heads are only $921 at Summit and would be a nice upgrade. A 331 or 347 stroker...
What combo do you have now? If you don't have a roller cam block this is a good time to upgrade. What kind of a budget are you looking at? GT40...
No problems in my area. Living just 2 blocks from the sherrif's station doesn't hurt :) I call my local junkman when I have a small load I don't...
Scare-Lane, that's funny. Car looks good, congrats to the builders.
1967 rear axles have the same 1 3/4" wide brakes and axles as 1966 and earlier F-100's and are I believe 1/2" narrower overall as well. 31 spline...
The 1" A-arm drop should be fine for a street car, the 1 1/2" drop is for those who want race car handling. The 1" A arm drop still gives better...
It doesn't work that way. If he is doing just the 1" Arning drop he does not need the wedge kit even if he uses drop springs. From DazeCars...
Pro Motorsports Engineering https://www.drgas.net/category.php?cid=29&catid=4 makes the ball joint wedges, various vendors like Mustangs Plus sell...
Yep I should mention some more "old" engines. Besides the 354 Hemi and the Y block there were the following: Two traditional Pontiac engines,...
The Hemi held on for 3rd going into the finals tomorow, the Kaase 429 Boss took the sixth spot.
I think that is the last engine to run, should be posted up soon.
They are running Webers see pics at bottom of page....
Dan Miller and Gene Adams 354 sponsored by Hot Hemi heads just took third place in the Popular Hot Rodding Engine Masters dyno challenge. For...
Yep I agree throw some 2.75 in there.
The original setup had an almost vertical steering column, there was a sleeved hole on each side of the frame for the bellcranks.
Anyone ever see this kind of steering setup before? Guy thought it was old Total Performance T stuff, it came off a t bucket. Looks like the...
Hawaii's favorite meat LOL. It's on the McDonalds menu even!
Got one here too, rusted out Sanborn tank, compressor/motor works fine. My buddy had it, didn't know why it couldn't hold pressure. I don't use...
In my 26 years in the Air Force I saw a lot of planes, one I alway remember is the SR71 takeoff at Mildenhall RAF in England in the 80's, the...
You are right that chart appears to be housing flange to housing flange but there are still several mistakes plus Ford had different offsets from...
That chart has so many mistakes I won't take the hour or so it would take to identify them all. <!-- / message --><!-- edit note -->
Can't tell without pics, my older 390 had a stack of 3 pullies COVERING the damper with the built in pulley, the built in pulley was not used.
Jay Leno is a real car guy, not just a checkbook writer. When he and his wife stopped by the now closed car museum in Shreveport a few years ago...
Also check out the new Edelbrock dual quad intake setup manifold part #7505 or the complete kit #2036 or #20364 for endura shine. About $1200 for...
I saw a hemi powered forklift in Stockton CA about 20 years ago, was stopping by a home machine shop with some buddies, I think one guy was...
Here's some aftermarket mounts that are way stronger than the factory ones. You need the FT302 http://www.autofab.com/2wd460.htm
The 1994-1998 351W roller cam block is the way to go. The casting number should start with F4TE. You can find these heads in late 1994-1996 F150's...
I say it's a Cadillac 368 judging by the TBI. From wiki 368 and V8-6-4 In 1980 the 425 was replaced with the L61, which was the same basic 472...
A 427 SOHC engine complete with fuel injection out of a boat for $3500 about 15 years ago.
Separate names with a comma.
The Jalopy Journal
