The Jalopy Journal
I had the PCV valve on the car when I had the oil issues.
The gas smell is strong. I am not sure how thin it is compared to how thin it should be. I have done nothing but drive the car since I bought it....
Ok, tomorrow I will drain the oil and check the plugs to see how they look. I checked my oil level and it was right in the middle of the fill...
I have no clue what my compression is. I will look for a set of new valve covers and see if that helps. I heard that adding a PCV valve helps the...
I had the breather removed, it is a grommet. The valve covers do not have baffles, but the grommets do.
Some pics of my setup Posted using the Full Custom H.A.M.B. App!
Ok, I have a 010 350 that has original heads and a tri-power with Edelbrock intake. I have a breather on the passenger side and PCV on the driver...
Sold, please delete Posted using the Full Custom H.A.M.B. App!
Here are some pics Posted using the Full Custom H.A.M.B. App!
This car is run daily, it runs nicely down the freeway and around town. The car sits low so it isn't the smoothest ride. 1948 Ford Tudor set on a...
Thanks for the replies guys. That is a great photo Don, thanks for sharing!
I am looking at getting a 51 Buick Super hardtop that has a dynaflow trans in it. How will the car do at highway speeds? I have searched quite a...
They sell any quantity you want. I have a couple full sheets of mild steel and a sheet of aluminum from them as well. Posted using the Full...
Where in SE Wisconsin are you? Posted using the Full Custom H.A.M.B. App!
Speedy metals has been great for me. I have bought as small as a 4" piece of 2" OD steel pipe. They are in Waukesha so it isn't a long drive. from...
I am looking to get some louvers in Illinois. I was told that there is a fella punching louvers in Harvard, IL. Anyhow if anybody has anybody that...
I personally have never found any that small. The smallest I have found are about 3 1/8. I hade to open up my center opening to get the push...
I did the rear one of my cars with the triangulated 4 link on the rear and a big notch. I got the kit from Gambino Kustoms. They shipped quick and...
Here is a pic of my 47 Posted using the Full Custom H.A.M.B. App!
Welcome from Milwaukee, WI Posted using the Full Custom H.A.M.B. App!
You have a lock up converter? If you do and dont have a lockup switch it feels like it doesnt go into 4th. Posted using the Full Custom H.A.M.B. App!
Saw this one at The Blue Ribbon Beer Run in Milwaukee last Saturday. Posted using the Full Custom H.A.M.B. App!
Take it off and sell it to me! Would look great on my 48! I think it looks great Posted using the Full Custom H.A.M.B. App!
Blue Ribbon Beer run is July 13 at the Pabst Brewery in Milwaukee. You don't want to miss out on this one.
Id just save the cash and buy somethin in 3 months. Posted using the Full Custom H.A.M.B. App!
Ok. Ill try out a stock converter and if rhat doesn't do it ill put a new trans in. Thanks for the replies Posted using the Full Custom H.A.M.B. App!
Thanks for the infop about the torque converter shop sounds like a good place. I unfortunately do not have a stock converter. Id like to get a...
Its not a locking converter. It has an 11" tci converter that is supposedly a 3000 stall Posted using the Full Custom H.A.M.B. App!
Can I pick up and converter from a th350? Posted using the Full Custom H.A.M.B. App!
I have a couple questions about TH350 torque converters. Other than the th350 and th350c is there any fitment issues as far as spine count?...
Separate names with a comma.
The Jalopy Journal
