The Jalopy Journal
March 2022 [ATTACH] [ATTACH] [ATTACH] [ATTACH]
[ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH]...
set up for a off the shelf rotor - -be it the 70-77 gm version- -or a mustang 2 stub for the 75 granada rotor to take a modern twin pot caliper...
(1) Facebook Tips and tricks, for the BASIC NOVICE please wall thickness, tig set up etc etc the 'do they need to be equal length on a street...
want to blast and paint lots of stuff so need lots of paint i am looking at epoxy primer - I want to buy a gallon or 5l apply it to fenders and...
[ATTACH] what are the measurements please - depth - return edgelosenge thickness, depth of the stiffenoing triangles [IMG] [IMG] [IMG] [IMG]...
What are the options what is available stock what thread sizes and pitches swap from differing manufacturers is a combined oil cooler at the...
can you please measure the location of the central front crossmember rivet hole forthe crossmember then in from the outer rail - and over from the...
Fusion 360 Tutorial— Get more with Live Review and add-ons is there anything to creating a HAMB group and sharing Early ford specific files...
NSRA Southern Swap Meet Autojumble - North Weald - March 2024 - Part 1 I couldn't link this to your reply so have put it here...... Fast...
hello using a metal flexible rule. measuring from the flat at the front and along the outside of the rail, coming in at 90 degrees to the central...
[ATTACH] ok what do i have or what is stock for a 35-40 chassis stock 40 spindles axle is 48.5'' to king pins all I have swapped in...
Rails arrived Have a 47 inch drilled axle and rhd stock 37 spindles So it's having hairpins Need all the front end parts No body yet. But do...
IS THE JUICE WORTH THE SQUEEZE, If you happened to have a few 35-40 chassis, and have some 32 rails would you fit the 35-40 x member, or buy one...
[ATTACH] [ATTACH] [ATTACH] question, is there a difference in a 1937-40 ford wishbone and a 35/36 wishbone from where the tapers start or IF I...
[MEDIA] just so you can see the difference thanks
pics and video please thanks
planning on switching the rear crossmember from a 37 to a 36 to lower it some, looking at the 36 crossmember, does it use the same 37-40 rear...
using stock 36 radius rods ... i have the radius rods - 36 i have a flatter 36 rear crossmember - going to switch it in are the springs the same?...
[ATTACH] The revlcip saw with the thin blades works a treat though
[ATTACH] 1. 37 van boby, front cut off at top of screen toast £250 2. 1937 van body, not very good £500 but twice as good as the above 3. 1937...
how do i do it? map gas little bottle and plumbers soft solder what flux am i using liquid or plumbers paste stuff its a walker rad and new, if i...
about two days
its the corvette chervrolet slip yoke c4 aluminium version that uses outy clips, because its aluminium and 1310 so they are a stock item ahh -...
[IMG] can you simply fit a model a type mounting in a 35-40 do you keep the output shaft centres the same as stock and then take into...
so, found a 8cm flathead and a english ford gearbox alredy set up for a flatty, was a 53 engine and had the wrong pumps - not 51 wrong pan - 3 rib...
step boxing possible? circular swaged holes cool stuff to copy
[ATTACH] I have mashed the perch pins swapping in a wishbone. I can't run the forward off the bone shackle mount pin shock tube mount as they...
[ATTACH] trying to work out what is stopping the oil from coming out........
buy some 35-36 rear radius rods leave them stock at the front IF they use a 1/2'' bolt to affix to the original torque tube that is a 1/2'' thick...
Separate names with a comma.
The Jalopy Journal
