The Jalopy Journal
He and a friend ( Chevy Dealer) drove from Ca. to Gene Jorden's shop in Kennewick, WA. to view my chopped '40 coupe. When it arrived at Gene's...
Mike, I'm having on going phone issues, could you contact me @ 360 385 7613 land line. Want to firm up the part purchase with you. On pages 3, 5,...
'54 Bel Air post sedan, with 12volt converted factory column. Using aftermarket 2 part plug connecter, has 6 ports, 2 for front turn signals, 2...
I have a Gen.1 wiring system in place in our '54 Bel Air post sedan. The person began Fuse Block / Terminal strip and Incoming lettered wiring,...
My son is wanting to have some openings cut into the hood of his Studebaker Speedster... He is the area of Walla Walla/Dayton/Tri-Cities......
Hey, asking for help on a Kwik Wire 8 circuit fuse block & terminal strip set up being installed in our '54 Bel Air post. This is the standard...
How many quarts of engine oil are required, add one for remote oil filter... Having trouble finding this information, have a 53/54 Chevrolet shop...
Lots of pieces, very little information as to where they GO..... A diagram would be helpful. Thanks, dyno Dave
Plan to install this gauge to deal with the usage of the three Carter YH carburetors, '54 Corvette stuff on my 269.85 cu. in. Chevy six, damn...
Have a friend that has been great help on my '54 Bel Air project. He purchased the " Lifetime" subscription back when, at this date has received 1...
[ATTACH] HELP !!! 60 CANADIAN PONTIAC 261 INLINE SIX THOTTLE LINKAGE DIAGRAM OR PHOTOS. The seller was told that the engine was from a mid-west...
[ATTACH] [IMG] [IMG] I started collecting these editions some twenty-eight years ago, these are the Subscriber "B" Issues, those sold on the...
Delete Thanks, dyno dave
Delete
Recently brought a vintage Chevy 216 Nicson dual carb intake that I'm fitting with Carter W1's, Red fuel lines and polished brass, etc. In the...
Just brought two Edelbrock intakes from the early 50's, going to accessorize and detail. Then market them and was hoping to come up with the...
Asking for advice on how to find and match up a replacement piston ? Have a balanced set, found one with a 1.5"crack on the lower edge of the...
no55mad, I tried to contact you with some header questions, the page is showing... " insufficient privileges to reply here"... Would you e-mail...
WHY ISN'T THIS SHOWN ON NEW POSTS ??? Thanks for the replies... Port Townsend rod builder Brian Austin had his trailer taken on...
Working towards a TCI II front end setup in my Bel Air, with R&P steering. The steering tube will be shortened for the shaft and u-joints. Need a...
Considering taking some lbs. off my '55-'62 flywheel. A '54 Bel Air 2dr.post, with a .040 over decked 261, milled #848 head, Corvette 3-sidedraft...
My P&G Model 300 Valve Gapper set-up arrived today, fairly complete seems in good condition BUT... Not the Outer Barrel & Base Adapter pieces...
Asking for some help in finding a source for the steel stepped alignment sleeves (3) per pkg. intake to cylinder head... These rings allow...
My turn signals have'nt worked well for long time. Would a newer switch assembly from say a '57 thru '62 fit in my stock column housing and...
Posting for a buddy... Bob Pontius is looking for photos/info on his old sedan that he street raced in early/mid sixties in the west Seattle area....
Have a '54 BelAir sedan and I'm gathering parts for installing a v8 Camaro/S-10 hybrid t5 into the car for street use. Using 55-62 car six...
A few months ago I got a 261 out of B.C.Canada, the serial #'s are different than the 235 examples I've seen. Casting # is 3769717 so it's...
Does anyone recognize a EP66 stamping numbers on a Patrick's camshaft ? The website shows the same .436 lift #'s on two of his grinds, but no...
Does anyone recognize a casting #CON4C109 on the block and is stamped #F3IIJC behind the distributor... 1958 truck 40series, I mentioned the II...
I installed Posies's #203 3" dropped rear springs and 1.5" lowering blocks in my '54 Bel Air in 1999, have driven 30,000+ miles since then. No...
Separate names with a comma.
The Jalopy Journal
