The Jalopy Journal
Does anyone know if the spider gear cross shaft inside of a 9.3 Pontiac/Olds positrac carrier is 9.3 only? Or will a cross shaft from another...
7481 850 Holley Double Pumper Carburetor, would recommend a rebuild, everything moves freely. Asking $225 plus shipping
What is the widest wheel that you are running on a 55-57 Chevy with the aluminum ball joint spacers? I currently run 4 inch wide Cragars on the...
Does anyone know what transmission fits this Chrysler Hemi bellhosing? I would like to use this with my 331 hemi. [ATTACH] [ATTACH]
Does anyone know what the dome CC is on these Jahns pistons? I am going to be using these in a 1955 265 engine and am trying to figure out what...
I have an Offenhauser 4x2 intake that I would like to run on my 409 Engine. I am planning on using Rochester 2 barrel carbs on it. Has anyone...
Is there a small block tripower intake that uses the large base Rochester carbs?
650 Holley double pumper part number 4777. Needs cleaned and rebuilt. Asking $150 plus shipping. [ATTACH] [ATTACH] [ATTACH] [ATTACH]
I am wanting to buy a '32 Ford frame for my '32 truck cab and bed. I am from Oklahoma so there is no place around my area that makes a frame that...
What would the compression be on a 1964 409 truck engine? I have read up some on these and it appears that there is a notch in the combustion...
We recently bought a very nice 1934 Ford truck cab but as usual the driver's door was hacked off at some point. I have heard that new doors will...
I am wanting to remove the T-strip that goes up the roof of my Model A coupe. I have a steel roof insert in the car. I just think the T-strip...
This is a 40 Chevy coupe project we have been working on. It's been a hot rod for a long time. This time it is going to be powered by a 10:1 455...
I attached a few pictures of a project I have been working on. It's a '57 210 2 door sedan. I wanted the front end raised so I went with ball...
Does anyone know if Pontiac/Olds 9.3 posi spiders are all on their own? Can you use spiders out of a Mopar, Chevrolet, or any other Dana style...
Does anyone know the length of a '57 Pontiac axle shaft?
I am building a '57 Chevy, I wanted the front end to be up in the air so I added some aluminum ball joint spacers and 409 wagon springs. I like...
I am thinking of buying some big block fenderwell headers for my 57 Chevy. The front end will be jacked up with ball joint spacers and taller...
Does anyone know if there is or was ever a 29 spline spool for a '57 Pontiac rear end made? I have a 29 spline positrac, but wouldn't mind having...
I have a 4:10 Pontiac 31 spline spool that I'm taking the spool out of to put in a '58 29 spline positrac unit. I dont have any carrier bearing...
I thought I'd share a few pictures of my model A coupe. We used some 32 rails, 40 Ford X member and pedals, Bronco 9 inch rear, model a front...
Will a 241 Dodge Red Ram hemi bellhousing and flywheel bolt up and work on a 354 Chrysler Hemi? Also, this Dodge hemi came out of a big 2 ton...
I'm going to use the M-50 Melling oil pump in my '56 354. I will also be running a rear sump oil pan. Does anyone out there make a new oil pump...
I have some adjustable push rods for a 354 Hemi. I see that hot heads sells one set for hydraulic lifters and one set for solid lifters. I have...
I'm building a 354 for my A Coupe and am trying to pick out a good camshaft for it. The 354 is a very nice standard bore engine, so we will be...
I have searched the forum and can't find an answer to my question. A friend is working on two Stromberg 4 barrels and the accelerator pumps are...
Here is our 57 Ford we hope to get back on the race track at some point this season. My cousin raced it in southern Oklahoma throughout the 60's...
Here is our 40 Chevy project. It will be powered by a 500 Cadillac with either a turbo 400 or 4 speed. It has been off of the road since 1973....
This is a nice message board. A lot of nice info. Anyway, I'm 'John Milner' and I just thought that I would introduce myself. I live here in...
Separate names with a comma.