The Jalopy Journal
I just finished this project this summer. Been driving it and shaking out the last bugs. This is as close to a nut and bolt restoration as a...
I've got an MSD in my sbc 283. I'm using Speedway gauges. I plugged my tach lead into the gray wire recommended for tach signal and somehow the...
I got this in a box of old carburetors, i don't recognize it. One of you folks out there probably knows what it is. Educate me and probably a...
here's a pic of the stuff. These all came off the same block. I believe these rods to be the Merc rods, if someone tells me how to verify, i'd...
I rebuilt this rear, planning to use it in my 59 Apache, but its gears are 3.90 and i don't have an overdrive, just a stock 350 trans. Would make...
complete assembly, came off together, starter plate fits the bellhousing. I don't know if someone wants just the hogshead, i'd gladly separate...
i have this 1934 Master 2 door sedan body and the patch panels shown in the pics. I'd say they are average, not great, not all rotted either....
Here is a pair of really nice EAB heads. I cleaned up the combustion chamber with a cheek poker, they cleaned up pretty nice. there is very...
these are kinda hard to find it seems, i ended up with an extra one. this has been soaked in EvapoRust, then sprayed with rust reformer/primer...
pretty nice pair of 90 year old plates.
I have these parts left over as duplicates, wanting to move them to someone who needs them. The front fenders are very nice i think, pitted at...
backing plates, came with a housing, i don't need them. i hit them with a little wire wheel, cleaned right up. i think i could stuff them in a...
Planning to get rid of the original steering box. I know there are basically 2 solutions and i'm seeking feedback from anyone who has done this....
Bought these but miscalculated, they don't fit my rearend. Near new condition, that's why i bought them. Ready to bolt on, be sure you know your...
got an MSD on my little 283, never been a points guy. Engine has started to miss and run progressively worse, seems to need more cranking to...
Very nice set of EAB heads, intended to use them on my last build, but went another direction. these have been soaked in citric acid, then washed...
these are all brand new parts, never installed. selling off excess FH parts. Distributor is a Speedway 910-0100, it requires a control box....
I sold the truck, here is an almost complete set of trim pieces. i have the fender pieces, but they are really beat up and really hard to package...
Found these on my shelf, bought a while ago. I think they are originals, not the repop Vintique stuff. trim is stainless, housing shows it has...
this intake is media blasted and port matched, ready to install. New generator nut, carb adapter, QuickFuel 450 cfm carb. Carb is brand new,...
Just finished this truck, really fun truck to drive. Lots of new parts, I'll run thru a short list. Contact me to discuss details. All...
Brand new glass, never installed. i bought the tinted vent glass, but then couldn't match the other glass tint, so i had to buy clear glass and...
This is a really nice Merc baffled oil pan. I soaked it in EvapoRust first, then found sludge under the baffle. I soaked it in gasoline and...
I've decided not to build one more flathead. I've acquired these parts over the last year or so, these parts are all new, still in packaging....
Just finishing this truck, decided i need to thin the herd. I'm reluctantly listing this.... To start, the driveline is all new, rebuilt motor...
here are a couple pics, my thoughts are this is the thrust end of the crank? I won't sell anything i wouldn't use myself, so let me know if this...
I'm digging through a pile of FH parts that came my way and i found a pair of heads stamped "A". I don't know anything about them, i'm certain...
I have 2 sets of EAB heads, both are pretty nice. The orange set is really nice in the combustion chambers, no pitting in any of the chambers....
I have an extra flathead blower intake. i had the adapter plate made, it is made for a Weiand 142/144 blower. I think this is a pretty nice...
I've routinely discarded the stock single carb intakes. recently someone mentioned that either the 3 or 4 bolt single carb intake, they couldn't...
Separate names with a comma.
The Jalopy Journal
