The Jalopy Journal
1- Came across a decent low mileage 2020 configuration 5.7 HEMI. I have a 1969 383 MOPAR hooked to a 727 torque flite. Will the 2020 5.7 bolt up...
In or around Phil’s / S Jersey Anybody know a good place to get frame & undercarriage of a friends 1940 Ford pickup cleaned & coated. Drove it...
I want remove posted classified for my ‘35 Ford. How is it done?
I’ve got a 40 Ford pickup. I had an optimum retool in it for 5 plus yrs that died. Seems the new optimum red top dimensions swelled & I can’t get...
I’ve had an issue w a 2-Holley 94 intake on an Offy intake on my ‘49 V8 Ford Flatheadp. I couldn’t get the idle up high enough without leaving...
Selling my ‘35 Tudor slant back very desirable model! Original body & chassis have 65000 miles. I am the 3rd owner & have the original bill of...
I’ve checked on The Hamb & Safari to find out how to get to classifieds on The Hamb? It says go to classified forum. believe forums is the last...
1967 442 ground lead connected funky. Someone just bared the copper strands & sandwiched them between the power steering bracket. & the engine. I...
I’m looking @ a 1947 Ford PU. It’s running a 302ci ford & has Lincoln Bendix type drum brakes on front but still has original non bendix rear...
‘67 442 came w 2 different water pumps, long for AC & short for no AC, higher volume on AC cars. Does anyone know what supporting parts...
I got a mid ‘60’s Olds 400 engine & replacing the water pump & don’t see bolts holing pulley on it so guessing I need a puller? Tried tapping w...
Bought a Ride recently with a mid ‘60’s BB Mopar. Supposedly rebuilt many years ago then owner died shortly after & kids left sit in garage. I...
Got an 8 3/4” Mopar open gears rear & housing assy. Thinking from ‘65-‘69. Question, will all the 8 3/4” housings it take a posi unit or is there...
I’ve got an 8BA in a ‘35 Ford, just put a bypass oiler on it that along with multiple carbs makes the rear of the engine too busy. I wanna...
In 1st gear there’s a vibration with quiet low pitch rattle. No slippage. Shifts fine to 2nd & after w/o any issues? Ideas?
Possible issue w Detonation. Cracked several pistons in land between compression rings. After new pistons installed want to make sure timing is...
Stroke on Master Cylinders Hi Guys, I need to know the stroke travel on both a '48 Ford master cylinder and a 65 Mustang dual master cylinder?...
Got a vehicle I just want to use as a worker. Don’t wanna put a lot into it. Got it running good and body not too bad but tuning the corner from...
I have an aluminum Offenhauser head on the bench from my 8BA Flatty for unrelated issue but noticed S-plugs protrusion into head chambers looked...
Running a '49 Merc Flathead in a '35 Ford, pulling it to replace w Chev SB & will B using the existing '39 tranny. Speedway has a Chevy to early...
Always had good results storing cars w typical hit list 4 storing except brakes. Always seem to be issues? Any tricks, additives process to keep...
My dyslexia screws me up with these two terms. Question, if I have 0 offset w 4” back space now & want to move the wheel further under the wheel...
Ongoing project to get one I bought in Sept on the street keeps "just one more thinging" me. thought I could correct steering issue on a poorly...
Bought Ride w a 383 Mopar that had been dormant in a garage for 25 yrs. Went thru the normal wake up procedures and have it running pretty good....
[ATTACH] Can anybody identify this rear differential? want to get a new chrome cover.
Bought Street rodded ‘40 Ford pickup a few weeks ago. Good advice here got brakes straitened out (portioning valve issues) . Moved to engine 383ci...
Working on getting a 383 ci Mopar started after a 23 yr nap in heated dry garage. I removed spark plugs & juiced cylinders up with combo of...
Got a Ride w a Mopar engine. Haveing trouble identifying from engine block #’s. Here they R 24681308 oil pan probably not original to motor but...
New purchase Ride that sat for 20+ yrs. disc front bled & worked fine. Tried to bleed rears ( drums) seems blocked. Pedal still high from bleeding...
why am I getting these messages on last thread created regarding my ‘42 - ‘48 Ford F1 chassis “You have insufficient privileges to reply here.”...
Separate names with a comma.
The Jalopy Journal
