The Jalopy Journal
I don't remember what year these are but I'd like to order new rubber hoses [ATTACH] [ATTACH]
Holy moly ! [MEDIA]
Seen this on marketplace, interesting how they did it. Maybe an engine for a midget ? " This is a 283 chevy motor that has been cut...
I'm in a position where I can't sandblast or power wash this frame do to being "locked in" a small garage. [ATTACH] I've scraped with a puddy...
**** Pre 1960 Event **** Less than 2 weeks until the kick off of the Drag Racing Weekend in Romulus NY. Weekend of Exciting Racing, Camping,...
On my 41 the tilt fiberglass doesn't fit great, I need to come up with a fastener that will both pull the hood sides down and suck them in. My...
Great show with a variety of rods and customs held this past Saturday [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH]...
Just got off the phone with the Painless tech and he suggested I move my orange wire over to the brown wire to hopefully increase voltage in my...
What's that extra blade for ? The continuity switches blades depending on if the switch is open or closed. The switches are for reverse lights...
At a local cruise, very nice car [ATTACH] [ATTACH]
Got this email today, hopefully Discovery doesn't screw anything up. [IMG] Hey there, Starting on March 25, 2024, the MotorTrend+...
This Sunday is the Snow Busters Automotive Swap Meet, all 250 + spaces are sold out, put on by the model A restorers club but there's a little...
What's the best orientation to kill the engine ? Placing the kill switch between battery and starter like NHRA normal rules. When looking at the...
Naturally first thing to mind is volts, but it's in a 12 volts system. Now I know they make voltage reducers but would big name aftermarket parts...
So you know how a parallel leaf can increase or decrease (depending on orientation) wheelbase under compression and deflection. Would a buggy...
I've did a fair amount of internet searching this afternoon but just not finding a formula. The springs are the Speedway gasser springs, 31...
I'm going to make some type of heat shield for my brake lines, bolt it to the lower two bolts under the master cylinder, to help the foreseen...
How do I set the forum clock to my east coast time zone ??? I looked around on my profile and account but didn't see anything.
Anyone use this Eastwood item ?...
A friend sent me these, what is it, can't recall a grill like that ? [ATTACH] [ATTACH]
I'm moving the brake pedal from under the floor up to the firewall on my 57 chevy pickup, for a variety of reasons, and there's a few different...
Little back story before I get into the nitty gritty, had this distributor rebuilt by a somewhat local guy that's pretty good, adamant about using...
I've been revamping my 41 over the last 3 yrs, bigger blower, bigger carbs, bigger fuel system from one end to the other, moved the alternator,...
What's the secret to installing these gems ? I can't get them to seat using a small piece of wood and a hard rubber mallet, even greased them up...
I've seen a lot of engines but can't say I've seen this strange bypass before. It's a 66 or 68 327 220hp, 4 barrel, manual trans, according to...
Will it stick to 50 degree sheetmetal ? Still pretty cold here and I usually work in 50-55 Temps in the garage. [ATTACH]
What would one look like ??? I got this storyboard from a neighbor's garage that was left there by a previous owner, reading all the details of...
Anytime I click on a link (to continue reading click this red word) in Ryan's threads I get sabotaged with spam when going back to the main...
I POR 15'd my Henry J frame couple years ago, did all the recommended prep, put on 2 coats and it laid out smooth. [ATTACH][ATTACH] I moved a...
I have this intake and the two rear corners at the water passageway in the heads are really corroded bad. It's deep to the point I'm leery to...
Separate names with a comma.
The Jalopy Journal
