The Jalopy Journal
Does anyone have any pictures or charts showing the manual trans side plate covers Ford used in their F 100 trucks in the mid 60's? Thanks
Looking for a clutch return spring for a 66 F100, I tried Carpenter, Drake and Rock Auto but no luck, any suggestions? As always, thanks.
Working on Ford in line 6 cyl. with points distributor, the engine started and ran fine one day and wouldn't start the next. I checked the...
When trying to start this engine it runs but raw gas is pushed out the top of the carb and some vacuum plugs are pushed off. Never had this issue...
Any of you guys had any success in removing the oil pan from a SBC while it was still living in a 40 Foad that still has stock front suspension?...
The intake on my 74 Ford 4.9 L (300) has three large holes where the carb bolts to it, two are stud holes any idea what the third hole is for?...
I am working on a 66 F100 that has a 75 300 engine (not running) installed in it. Should I use the original (still installed) 75 HEI distributor...
On a 66 Ford F 100 does the voltage regulator mount to the fender well or radiator support? I am trying to reassemble a project I did not...
With the clutch arm location at 7:30 does the arm hit the un split wishbone on 1930-40 Ford cars? Thanks!
What are you guys doing about brake pedal hitting clutch fork when using SBC in early Fords? I did a search prior to creating this post. Thanks...
After looking at pictures of the 39 Ford clutch pedal assembly, isn't it set up to push the stock clutch fork? When using a SBC clutch fork set up...
Any of you guys ever adapted a clutch cable on your street rods? Thinking about trying a cable set up on my 40 Ford with SBC and looking for...
I was hoping to use block huggers headers on my 40 Foad coupe with a SBC on a stock frame but they don't clear the stock steering box, are there...
IF I decide to go with auto trans on my 40 Foad and use a Speedway split bones kit will have to adjust the caster? If so, how do I do this? Thanks!
I would like to hook a 67 Olds two speed auto trans to a SBC, has anyone ever done this? I would like to know what I would need to do this....
Relocating the battery in my 40 Ford coupe to the trunk, what size cable (gauge) do I need to use? Thanks!
It is a bitch getting old (late 70's), I was mistaken about the starter, it functions fine, the problem is the generator keeps turning after...
Installed new starter switch and no change then I bypassed the switch altogether and ran the coil off the battery and the same thing, starter...
The starter on my 1950 3100 Chevy keeps spinning (not the bendix) after engine starts and when the engine is shut off. The only way to stop the...
Why not use a 12 volt generator on my 50 3100 Chevy instead converting to an alternator? Thanks
41 Laselle transmission, column shift.
Complete 40 Ford Coupe running gear, 85 H.P. engine (seized), transmission and banjo rear.
Does anyone make front brake drums for a 40 Ford Coupe with a 5 X 4 1/2 bolt pattern? Thanks!
I want to run Ford wheels with a 5 X 4 1/2 bolt pattern on the front of my 40 Ford coupe using the original drums. Who makes adapters for this...
When I removed the front brake line that runs along the front crossmember on my 40 Ford the line was behind the crossmember, the new replacement...
Headed to junk yard and was wondering if you guys could suggest what to look for. I need a drive shaft 55 inches in length that would accept a GM...
I just finished installing a 67 Mustang 8 inch rear end in my 40 Ford Coupe using the TCI kit which worked out well, the only issue was the...
Complete engine (seized), transmission, torque tube, banjo rear end and radiator out of 40 Ford coupe.. Engine is complete with starter, carb,...
Several years ago a gentleman from Oregon used to make a floor shifter that would mount at the top of a transmission instead of the side. I...
We all know that rear transmission yokes slip in and our to compensate for rear housing movement, how did these issues work with torque tubes?...
Separate names with a comma.
The Jalopy Journal
