The Jalopy Journal
428 crank is a 1U, wet magged and checked straight, .010/.010 with inserts Forged Sealed Power .040 over later model pistons with .040 over moly...
I asked that my second post be deleted as I had my first post deleted as well ............................... Thank you for deleting the post...
I did not know what section to post this in so I chose hot rods Daddy put a Rocket olds with shaved heads, put ball bearings in the lifters to...
I posted a while back on shaving the tops of my pistons and got lots of ideas ( Many thanks yall ) There will be plenty on top land and valve...
Question: you have 8 x V8 rods, balanced on little end and balanced on big end on a rod weighing rig They all weigh 750 grams, you machine...
.-40 over 390 block, 390 forged pistons, 428 crank.... need around .083 shaved off piston tops Plenty of top ring land will be left and piston...
I have an early Edelbrock F380 FE intake with the small carb flanges Also have 4 WW Stromberg carbs off of early Dodge truck poly 318 mills Any...
1965 F100 Have talked to Folks at car shows and cruise ins .. read online about the rules as well Each seems to have a different understanding...
My Carter Competition Series carb has a 3/8 fitting for a rubber fuel line My rubber fuel line is 5/16" ... do you have a solution so I can...
The Space City Cruisers an other Car/Truck shows have opened up Catagories a whle back, slowly ..... but needed for Foreign ( some call ricers )...
I have Holley 80457-1.. the rear seat is not sealing It is an older version than the ones on Holley's site Also have a fairly new sealed pack of...
I need a pressure washer to clean parts and sometimes small mold spots on my brick house Any advice, it will not be used much Ricky.
J2 9400S There are no rear jets nor tapped holes Anyone ever seen one like this or know what the reason was for ?? In the rear fuel bowls are...
65 F100 is down to 3700 but will be around 3200 or lower when finished What size, thickness and such tubing would be appropriate strength wise ??...
Not sure which vehicle this came from [img] [img] [img] [img] Ricky.
Have a 50's F100 axle that is a tiny bit lose as to king pin fit With a king pin in, there is around .001 movement With the king pin halfway in,...
They were all together with gaskets and such, had a faint smell of gas Have not soaked or cleaned them, this is how they came apart Ricky.
Short wide 65 F100 .... bed floor and wheelwells are going away, just bare fenders Attaching them to the rear of the bed, will make new...
These have been in my closet for a long time They were washed and dried on delicate I have looked them over and tried to point out any flaws as...
Thanks Ricky.
I have a Ford 9" 3.75 with an Auburn cone type LSD I have read on various sites, as they wear, they introduce fine metal dust into the 3rd member...
If one was to shorten up the throw on a 3 speed manual column shifter a bit Moving the holes closer on the column arms to the column ? Or moving...
61 to 66 F100 parts ..... hoods, bumpers, tailgate outer skins, etc US Body Parts now wants $700 plus $300 shipping for a hood with full pay and...
I have a ton of FE parts I could sell to finance a gen 1 hemi for my old truck Does not need to be fancy, always wanted a hemi for the looks Truck...
Ricky.
For rebuilding or core Will fit in Large flat rate USPS priority box... $21.00 shipping Rochester Quadrajet 17082224 1692 F JP Has some...
Was reading this old thread and thought I would ask https://www.jalopyjournal.com/forum/threads/carter-dual-quads.818648/ I have an old...
Mopar 833 OD 4 speed trans .. A or b body tail housing NOTE: This an Over drive transmission The tail housing is cast iron .. the rear...
Any know how much a 1953 to 1960 F100 front axle weighs with or without spindles ?? Humor me please .. EDIT: No, not gonna buy a 64 or down...
Any know how much a 1953 to 1960 F100 front axle weighs with or without spindles ?? ....EDITED ...Any know the king pin inclination on the above...
Separate names with a comma.
The Jalopy Journal
