The Jalopy Journal
Chassis & 4 Bar Parts, 8 Weld On Tabs, 2 Weld On Brackets, 2 Spacers, 2 Weld On Split Rod Ends, 4 CM-7 Rod Ends Are new. The 3 Rod Ends in picture...
NEW COMP CAM 903 VALVE SPRINGS Complete set of 12 valve springs for a 240/300 motor build may fit others. This set is new, never installed, in...
Old28 Member from Camarillo, CA New City: Camarillo State: California Price: IN AD SRP 4.500 Tapered Aluminum Piston Ring Compressor. Like...
Old28 Member from Camarillo, CA New City: Camarillo State: California Price: IN AD 4.310” No Name, Jegs or Summit (not sure) Tapered / aluminum...
4.310” No Name, Jegs or Summit (not sure) Tapered / aluminum Piston Ring Compressor. Like new condition, Only used a few time on my race motor....
4.310” Jegs or Summit Tapered / aluminum Piston Ring Compressor. Very usable condition, Like New. Price -- $22 + $14.35 USPS Medium Flat Rate Box...
COMP CAM 903 VALVE SPRINGS Complete set of 12 valve springs for a 240/300 motor build may fit others. This set is new, never installed, in...
[IMG]
Three Ford 94 carb bodys, basses, assembly small parts. There is 95-100% small parts to put the carbs back together. All three will need full...
This Ad Is Closed See New Ad For Holley Jets Only ! New Lower Price [IMG] [IMG]
New Carb to Intake Manifold gaskets for Ford / Holley / Stromberg two barrel with 3 bolt mounting. 12 total in three different styles. See...
All NEW IN Original Package) Main bearing brass shims, un-opened package, Bratton's Antique Connecting rod brass shims, un-opened package,...
This is a complete ready to install 1932 B Transmission case with the model B upper flywheel adapter and lower flywheel cover. Transmission has a...
All parts came off a running motor. Lots of good reuseable parts or good core. 1 – Stock A iron head, No visible cracks----------- $10 3 -...
I am looking for a supplier to buy a Hi-Performance head gasket for a Ford Model B motor that has a bore of 4.030". This is a mild race motor...
Working on a motor/trans/clutch setup for a project. Motor will be a 75-85 HP with lightened A flywheel. Would like to stay with a model A clutch...
Is this the right place to start a build on a TROG racer? If not set me straight! Tom
[IMG] Lightened Model A Flywheel Trying to figure out how much weight to take off a Model A flywheel for my TROG race car. Car will be run in side...
I am building a 32 B trans to go on a Model A motor. I have a couple of questions. Will a 4 cylinder 32B upper flywheel cover bolt directly to an...
Looking to put a pre 53 rear end in a TROG model a frame. Can any one help as I am not up on pre 53 rear names or gear ratio. I under stand 8.8 /...
I have a set of six new chevy 6 cylinder 292 stock D shape dished pistons. They are .040" oversize. They are complete with new pins. I got them...
Does anyone know if TROG rules are ok with fiberglass bodies? I know that car body must be a pre - 34. I am looking at building a 1923 or 27 T...
Looking for some information on Ford A & B Motors. 1 -- Will a 1939 Ford top loader trans bolt direct to the A or B block? 2 -- Is an adapter...
I would like some information on matting a 1953 chevy 235 motor to a older cast iron powerglide trans. Was an adapter used between the motor/trans...
Looking for a little information on the following engine/trans combinations. Does anyone make adapters for these combo? 1939 Ford Trans to a Ford...
Ryan, hope I am not stepping out of bounds letting readers of the HA/GR forum know that my SDRA dragster is for sale in the HAMB classified "car...
SDRA / HAMB Style Dragster HOPE IT GOES TO SOMEONE THAT CAN HAVE SOME FUN NOSTALGIA RACING, YOU WILL NOT FIND A TURN KEY DRAGSTER FOR LESS...
Separate names with a comma.
The Jalopy Journal
