The Jalopy Journal
[ATTACH] I have looked in a lot of places and can't decipher the last 2 on this serial number. I know it's a 67 427 4 bolt main with forged crank...
2 years later and it is still holding fine, no noticable rock chips, flaking or peeling. I have took my truck through the woods and had limbs run...
I bought the car about 2 years ago and was working on putting it on the road. Last summer I was close and had it at a buddies doing the floor...
I got my head light buckets off eBay, does anybody have any dimensions on the small marker light lenses that go on the buckets. I'm trying to...
I spray it outside of my shop. I spray it out of a schutz gun it sprays just like normal rubberized undercoating and the results I'm getting its...
http://www.ehow.com/list_5856429_types-vehicle-undercoating.html. This might be an interesting read
If I lived close to a paint supply that had it I probably wouldn't bother. I'm 40 to 50 miles from the nearest good paint supply. Which turns into...
The mixture without the paint and hardner is too soft for the undercarriage and may soften up even more with heat from the motor. If anybody tries...
I'm not shooting on bare metal body parts I'm shooting frame, running, inside body parts that are normally ready for undercoating. I'm a...
24 hours later it is set up, you could handle it but its not hard like the other yet. It takes some pressure but I can cut it with my finger nail
Its not so much about the money. I have have guns I have more money in than a few of my vehicles. Undercoating from a paint supply is $60 and its...
Road runner have you ever used it? And will it harden up enough not to drip when it gets hot outside? Lowes carries it for $52 for 5 gallons. If...
Depending on car. My f250 I sprayed the frame with the bed off and partially sprayed the bottom of the bed and used a gallon at $60. It would take...
The mixes were in the initial post and were guesses. I just sprayed some that was just the leak stopped and lacquer thinner. I'm waiting for it to...
These dents were done with a 14oz ball peen hammer hard enough to cave in the tail gate.
It is a odd mixture. I have a hose that hooks to a shutz gun for inside rockers and hard places to get to. When I spray rubberized undercoating...
I think I've found a pretty decent way to make undercoating. Lowes carries a rubberized roofing patch in a red can called leak stopper $16. I got...
I'm looking for shows,swap meets, or old junk yards in the Maryland or southern Pennsylvania area. Will be in area until the end of sept.
south east but i have the weekend off. so i can travel. i had talked to a guy named chris that was from up here somewhere that had a bunch of...
david in texas had some nice fenders and other parts last time i talked to him. send me a message if you want his number. he has a small junkyard...
does anybody know of any junkyards holding old cars in the pennsylvania area? im here for a few weeks and always hunting parts.
dont know if you ever found out but that looks close to the same as mine, mine has been cut 7 inches in the front. i cant remember my windshield...
i am a welder by trade. if you are mostly working on your car or small projects around the house a high amp 110 welder that will go at least 135...
if you knew somebody in georgia or another state who uses a bill of sale you could probably get iowa to recognize that. i think la still uses a...
double hump heads to the best of my lack of knowledge were on 327s not 283s so at some point they have been changed. there is another way to...
i went today and the old man at the yard wouldnt let me in and its 25 here
its just my 2 cents but mine has a 50 ford glass in it. its a lot flatter than the merc. and dont have the curved sides to it. i havent measured...
Separate names with a comma.
The Jalopy Journal