The Jalopy Journal
Can crack even the hardest nuts.
I wonder if the original Ford drawing even has that dimension on it. But it would be nice to get a handful of members to post what they've got so...
Had one on a jobsite doing lite structural iron. Worked great on 3/8". Had to watch the duty cycle at those amps. But it was awesome. So...
My wife believes that I am her trophy husband. Not giving that up.
One drawback to not having the crank threaded is the camshaft gear is not locked in place as it would be if you had the bolt to tighten the...
Got a 1930 Cadillac manual trans here that has a PTO driven compressor pump. From the factory. So, if you have a trans with pto capability, it...
Who'd a thought that we would find, yet another, use for WD 40.
I've thought about this for some time. I assume you a not using running boards. But to cover and protect the brake rods and to give the bottom of...
Had an old pickup that was rusted out like none other than I've ever seen. Ran good. Came across a guy selling one with no engine, trans or...
I've never considered cars and trucks to be investments, but I always make a profit on the ones that were bought to flip. I usually buy it, make...
I bought an OT truck, sbc 400 with dual exhaust. It was smoking bad out of one side and perfectly clear on the other. Needless to say that I got a...
This is a complete engine trans combo from the fan to the ujoint. Carb to bottom of oilpan. Was pulled from a car some 50 to 60 years ago. Not...
I bought this new. Took very good care of it. Still looks like new. It is set up for gas. Includes flow meter, no bottle. Requires 125 volt, 30...
Me too. My dashboard hula dancer needs replacing. She just don't move like she used to.
Or use Secret. Strong enough for a man but made for a woman.
I think I'm past the piling shit in the corner type hoarding. Recently came across a nice lady selling off her dear ol dads lifetime collection of...
Make sure the kingpins are properly lubed. If the zerks are bad, change them. Try greasing them with the tires off the ground.
Must of been one hell of a vacuum leak.
How large of pulley? Too big of drive pulley could make the motor work harder. If you go that way, check the max. amp draw of the motor. Make sure...
Next time you are plumbing your building for air, use the largest diameter pipe feasible. This adds more capacity to the system. Much like adding...
My remote horn is my middle finger. Don't use it too often but when I do you can be sure that the other guy hears it.
What gets me is it seems like all the new compressors like Ingersol, Husky etc. all shut off at 175 psi. Why? All of them are driven at 3500 rpm....
What I used to do with waste liquids in the past is a secret. Nope...I won't tell you. Now I have some five gallon jugs that, when full, I take...
Eaton corp. sells a nice line of pumps. Good customer service. I like the low rpm compressors. They are quieter and create less heat. Bought a...
Driving across Missouri in a strong headwind. Snow blowing all directions. Temps in the -15 degree F range. Amp gauge goes to the negative side...
I hear that doing a certain something will grow hair on your palms.................Made you look!
For added cool points they should cast "MADE IN THE USA" into these parts, if applicable.
Getting ready to start on one any day now. Bought a complete V860 with trans. It's going in an A frame. I'm going to keep the mechanical brakes....
I was having problems with what I believe was vapor lock on a small block 400. It would not restart for 10 minutes or so till things cooled down....
Drive to a dark parking lot. Turn the lights on. Adjust one at a time by covering one and adjusting the other. Set the left one to focus on the...
Separate names with a comma.
The Jalopy Journal
