The Jalopy Journal
I tried a Haddock but found it took too much fishing around to hook it properly
Brilliant !!! Thank you for the considerable effort of taking super pix and quickly posting them. It is great to be able to virtually attend a...
THANK YOU !!!! for your extensive coverage of this large event. It is reassuring to see such a large turnout and so many early hot rods and drag...
Again, I suggest that you simply call Joe Hunt and hold on till they answer and then describe your situation.
When I went to install my "Mag Look" distributor it would not go all the way in - I called Joe Hunt and after a goodly wait I was told to cut off...
I strongly support all the positive comments by others above. Pat's writings are always extremely well done and wonderfully illustrated - If you...
Thank you for posting - A real car involved event is a fine thing !!! Any chance of pix of cars on the hill or , dare I say it, a video of the...
rob-redm - Would appreciate learning source of your rebuilt transmission - Thanks in advance for your answer DW
A bound Xerox copy of all issues of Throttle Magazine starting with January 1941 through the Nov - Dec 1941 combined and final issue. Many, Many...
Would appreciate advice as to the correct spark plug gap when using Joe Hunt Mag Look Distributor in 49-53 8BA Ford with Autolite 216 plugs -...
A wonderful period, the 1940s. An ultra wonderful car to celebrate the 1940s !!!!! AND IT IS DRIVEN.
SOLD - SOLD - SOLD Pair of aftermarket spindles have bushings installed and are brand new and never mounted. Pair of aftermarket steering arms...
Sloppy - Thanks for reply - Nothing for me but being a day late and a dollar short!! - Would be nice if someone at Hudson had gone through their...
In 1957 we ran a dragster in C Dragster Class at Orange MA Airport drags and in B Open Gas Class at Sanford ME, The car had a front mounted...
SOLD !!! SOLD !!! - Drums have bearings in place and have no pitting and have no wear ridge at edge of shoe surface - Backing plates were...
A short piece of black plastic electrical tape INSIDE the cover - Easy on and easy off and no clean up
[ATTACH] [ATTACH] Original fuel pump block off plate from the 1950s in unopened original packaging - FREE SHIPPING
Have 32 Hiboy with front tube shocks that measure 15 1/2" installed height - Have original early F I pickup upper shock mounts and bottom of...
The use of "Sing, Sing, Sing" was a super fine addition to a very well done video
SOLD ! 1935 -1948 Ford 3:27 Ring & Pinion with Timken replacement bearings installed 1000 miles ago - 36 tooth ring gear - 11 tooth pinion...
1926 Ford “Lakes Modified” Roadster Chassis: Custom fabricated, featuring ¼ elliptical springs both front & rear. Dropped front axle &...
Am confused here - Summit page for 29219 coil says coil has a resistor so separate one not needed and Mallory Instruction diagram for magnetic...
8BA flathead, generator, voltage regulator,Mallory Breakerless Magnetic Distributor, Mallory Ballast Resistor, Mallory Power Cell - Unable to...
YES DOROTHY, THERE IS AN ALLARD QUICK CHANGE ! Photos 1 & 2 show open and closed sides of an Allard Quick Change - It has been updated with a...
2 Piece Fire is Custom Fit for 6'4" 210# and pants are probably 38-34. Suit has SFT Cert 3.3 arm re[ATTACH] [ATTACH] [ATTACH] [ATTACH] straint...
SOLD - THANK YOU
Brand new, never opened full gasket set for 365-390 Cadillac engines from 1956 to 1962 - Free shipping to lower 48 only[ATTACH] [ATTACH] [ATTACH]...
For doubters on our last post on this subject please see the attached, which is a page from the October 2013 issue of the Allard Owners Club...
Stiff opaque/grey white plastic washer under bolt head or it will leak from under bolt head and, of course, the black rubber gasket under cover...
Am in the market for a set of reproduction 35 Ford hubcaps and would appreciate views on quality by vendor - Macs & Ford Barn $20, Speedwy $25,...
Separate names with a comma.
The Jalopy Journal
