The Jalopy Journal
Cord 811 Posted using the Full Custom H.A.M.B. App!
Well in my case raising the motor by a 1" wont fix my problem i´ve tryed it yesterday. The middle tube wont hit just by shimming the donut so it...
Would Two hockey pucks do the trick ??? Otherways its time to spin a chunk of aluminium in the lathe Posted using the Full Custom H.A.M.B. App!
Btt Posted using the Full Custom H.A.M.B. App!
Hi Dick I bought a pair of Bob drake 48 truck pumps . Posted using the Full Custom H.A.M.B. App!
Hi there I recently bought a pair of fenton cast headers for my 37 ford. According to the ad they said to fit a 37 ford with stock steering....
Hi I have recently dissasembled my 1936 ford gearbox. Inspected it Cleaned it up replaced bearings and som other parts. It had the early...
Hey Thank you for all response.. I was planing to go under the x member just to clear the pedal stand master cylinder and brake pipe.. The...
Hi Need som advice here about building the left side exhaust on a 37 ford Wich is the best way to go. Through the x member stand or under the...
What kind of ballast resistor should i use....??? I cant se any specs in the users guide of the distributor ????
it is not a stock engine .....High rise Thickstun intake ,dual 97:s, mercury crank and a max 1 camshaft i thin k it will rev pretty good......
I know but i am planning to use a magneto when i have the cash for it meanwhile i want a new and fresh distributor for my 8ba....
I am choosing between Mallory unilite or Mallory dual points distributor for my 8BA engine... I dont know very much about the unilite...
I was building a race mopar 340 a couple of years ago to my barracuda 67. All moving part in the engine was new and the engine had not been...
My old lever action shocks were worn out so i needed to figure out something to make the car ride nicer on the road. First of i needed...
This is a original 36 to 38 transmission i purchased to use in my project. It has not been running since i bought it. There is no visible rust in...
I have tried both and it wont budge even if i hit the syncronizer with a rubber sledge ...
Hey I have a stuck syncronizer hub on my ford 1938 transmission... I need suggestions how to make it slide again.... Christian.
I made a circuit from the alternator output to through the amp meter to the battery positive... My ampmeter shows a high reading when the...
I see that the link above is wrong sorry...The correct chemical i CRC rost flash................
Hi there I´ve been very sceptic about miracle chems but i´ve had only good experiences about this one when removing stuck bolts...
I converted my 1950 special to 12 V with a chevy 100 Amp Alternator---I just drew a new wire to the am meter with np so far and has driven it like...
Hi again I am talking about the front plumbing. From the main cylinder the line must go past the area were the x bar merge with the main frame...
Ok thank you The one thing that i hav´nt been able to see on any picture is how du the brake line go past the area where the x link meet the...
Hi there I have a ford 1937 frame wich i have converted to fluid brakes. The problem is that i dont have any clue how the front brakelines are...
Yes i felt like the title was kinda unfair.. Anyaways The manual that followed this kit said i should use 1 of the old holes in the...
Hi Ive recently bought a bob drake 39 brake/clutch pedal stand to save me some time when converting my 37 ford to juice brakes. I used the...
Hi Ive recently bought a bob drake 39 brake/clutch pedal stand to save me some time when converting my 37 ford to juice brakes. I used...
Some 10 years ago i was replacing the brakeshoes on my 67 Galaxie. When mounting the new spring between the shoes i used my arm against my knee...
Separate names with a comma.
The Jalopy Journal
