The Jalopy Journal
I have front mount, bell housing adapter, flywheel, 3 finger clutch, trans adapter, dust shield, bolts. This kit allows you to install a small...
72 chevy 350 truck block. 4 bolt mains 2 piece seal, LH dipstick, 1995 truck oil pan. Hot tanked, bored, honed, Block decked .008”, New cam...
Thanks Moose!! Looks pretty awsumme
[IMG] heey Moose! Would it be too much trouble to see what my old truck would look like with flames? Sent from my iPhone using H.A.M.B.
Great thread. All these trucks need is a little love and half a bucket of money. Sent from my iPhone using H.A.M.B.
I have a rh front spring hanger just sitting around. Yours for the shipping. Also have springs f&r, a 59 rear axle housing, etc. Put a kimbridge...
Brand new set of block hugger headers, fit ZZ4 engine, slant plugs with R/H dip stick, or aftermarket aluminum with slant plugs. Comes with bolt...
This speedo has been sitting around almost 60 years. face and needle perfect, needle free and floating. Needs cleaning at a speedo shop after all...
I have the vent doors for 55-59 chevy truck, $20 each. original black plastic vent pull cables, $5 each vent grilles, large and small, $20 each...
City: Phoenix State: Arizona Price: $100 City: Phoenix State: Arizona surface tust. [IMG]
City: Phoenix State: Arizona its $20 Price: $75 USD City: Phoenix State: Arizona Price:$20 usd City: Phoenix State: Arizona Price: $20 usd...
1956 chevy engine short block and heads.... has oil filter but no side mounts. Comes with block, crank, rods, pistons, heads, rocker covers. short...
I have the vent grilles for right and left inside cab vent ducts. no rust, no dents, not bent. one is the large one, and one is the small one....
City: Phoenix State: Arizona City: Phoenix State: Arizona Price: $600 usd [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] corvette aluminum...
1957 chevy truck flywheel, not stepped, $75 1955 chevy car flywheel, $75 1959 chevy 283 flexplate, $40. I have 3 Brand new 10 inch clutch with...
This panel has been plastic media blasted, relieved for independent front suspension, and then powdercoated on both sides. No rust, professionally...
These wiper arms are the ones installed under the dash, and bolt to the wiper motor, and have the posts protrude out the fresh air grille in front...
Original Fresh air grille. This is the vented body panel that is installed in front of the windshield just behind the top of the hood. This part...
Spare tire carrier. Pulled from an Arizona rust free truck, comes with the hanger stud, cross bar, and the bolt- in cross member associated with...
I have some things for 55-59 chevy truck brake backing plates, F&R$15 ea.- steering box $40, original steering wheel drums $20 ea, shoes , brake...
Heads are 202-160. They have been machined for late style oil seals. They have bronze valve guides, screw in studs, hardened seats were installed....
I have had the shortblock sitting since 1989. Heads are powerpak with triangles over the flats. The heads were off the engine out of my '57 chevy...
I bought my 57 chevy truck for $150 in '73. I fixed it so it'd run, and have been using it ever since. Since it finally got to me that the brakes...
Was it an auto trans before the 4 Speed? The clutch linkage goes between the frame and the engine. If you have a broken mount and you are torquing...
Why would you heat the steering arms? just make a two holer spacer that resembles the shackles, and sandwich it in there betwen the backing plate...
go to transmissionhead.com They have a vss/ speedo drive that will fit right in that trans, yea it's $96 bux, but when you put the throttle body...
Ya know, I always wanted to build a pickup with 2 chevy sixes side by side just to see what the torque was like........I think I can do it if my...
Voodoo, Because of how the total install worked out, I should have gone the route that you did, but now that it's done, I wish to fix the problem...
That's all well and good, but what front end are you running?
I guess dropping the back some more might fix the misperception, but maybe the taller spindle will work for the camber gain?
Separate names with a comma.
The Jalopy Journal
