The Jalopy Journal
Thanks Ronnieroadster, I will back the vacumn brake off. I also wondered about the small amount of timing advance. I really appeciate you reply. Ron
I thank all who chimed in. This is a great forum with a wealth of information. If and when I figure this out, I will let the pertronix people know...
as I have heard I need at least another set of points and condencer because the good ones are so hard to find. I understand that some folks hate...
Thanks for all your help and ideas. I will be calling the tech line tomorrow!!
128p6 6 volts pos ground. lots of grounds, clean, engine starter, frame, none to distributor. Many have generators with no issues. Thanks Ron
set up on a sun, vacuum brake on and set up at the time. Thanks
older rebuild, .060 over. Rebuilt gen, usa voltage regulator, all work good. Thanks for the reply.
Thanks for your help!! Flathead is stock, single carb
I have a 59 ab crab distributor flathead with pertronix installed. Starts fine, idles fine, no misses. At a little over 2000 rpm it starts to...
$3800 material, $3000 labor, 1939 standard 2 Dr sedan. Ron
Thanks all for replying, more information than I thought! Ron
I don't have a dropped axle, and lt is a unisteer rack and pinion manual cross sreer for 1935-40 ford
I hope this is the right place to ask about this set up. I bought a 39 Ford with this set up and have never seen it before. I got it from my...
After looking through this post many times, I kept telling my self no way. I have a 39 ford standard 2dr sedan with only parts of the headliner...
Working on my 39 ford and wondering what people are using for door panel and kick panels behind the material? I have the originals and can use...
I posted on the barn, no luck. I'm missing some of the tack strips for the headliner and wind lace on my 39 ford standard 2 dr sedan. I'm trying...
Just wondering if anyone has used a mirror inside their car trailer. Until I get almost inside the trailer, I can't see where I'm at. I was...
Any one used a WLS headliner? I need a headliner for my 1939 ford sedan. They are made to fir 38-48 ford sedans, mostly good reviews. Not many...
Sorry about the title Too low on the snubbers.I just got a 39 ford sedan with small block chev. All new front end, rack and pinion. I believe it...
Thanks all! I know it won't look as good as a roaster, (specially with my talent), I just want to make it look as good as possible. I have seen a...
Sorry! I want to leave the top off, and finish the doors and around behind the seat. Thanks Ron
Coupster???? I have a chance to buy my brothers 29 sport coupe, all apart, 2 frames , most parts, no top frame or material, engine or trans, 8"...
I have a very nice mostly stock 1936 ford pickup. It has very old Firestone bias ply tires that look new with nubs still showing. I need to...
Thanks for the replies, still not sure if I'm going to tackle it. Major project. Ron
I have a chance to buy a 29 sport coupe, in many pieces. Just wondering if anyone has left the top off. I have not found any top bows or top. If...
I have cleaned and rebuilt my 94 carb on stock .060 59ab. Engine starts right up and idles great. It has the correct 7.5 power valve and 51 jets....
I need to replace the front spring on my 36 ford pickup. I need to know the correct uninstalled length to order the right one. The spring that is...
I need to install new door glass in my 36 ford pickup. No glass was in the doors. The old glass had channels on them, but were installed different...
Thirdgenauto or 35tn, on ebay. I just saw one for $13. Ask on Ford barn. Ron
Separate names with a comma.
The Jalopy Journal
