The Jalopy Journal
Those oil lines look great, just getting started on mine, been gathering stuff for a few years now[ATTACH][ATTACH]
I am pretty sure the wheels were on this ride, I think I have a better picture, if it can be found?[ATTACH] [ATTACH]
I was able to score these wheels last week, wondering what they might be[ATTACH] [ATTACH][ATTACH]
I am trying to get a dash ready, too many choices[ATTACH] [ATTACH] [ATTACH]
This sounds like what i need to do, Did Don Ferguson do the work for you? I spoke to him on the phone, not long after I bought the heads, but I...
I am getting ready to build an engine for a NOS set of Ardun heads. The heads have the stock seats, as seen in the pictures, and I have concerns...
[ATTACH] [ATTACH] [ATTACH] I went to put some gears into my quickchange this weekend, and I seem to have a problem. the lower shaft has a sholder...
2 jumper wires from the condensers to the dual coil plate did the trick, I now have spark at the plug, thanks
The Coils that are on it now are 6 volt, I do not know if they are any good or not? I do not have the engine or Distributor grounded, other than...
my question is where does the negative terminal of the coil go? should the negative side of the coil be grounded to the engine or frame? The...
[ATTACH] [ATTACH]
I need to purchase a chopped top and windshield for this roadster I am working on. any info on where or where not to go would be helpful. Labon...
I do not have measurements handy, but here are some pictures of my set-up. it is further along now. with a different master cylinder...
is there a banger meet, this thread seems to be a promotion for bangers in general, not about a particular event. If there is a banger event, I...
Here are more pieces and parts that came with it, magnets in the brown paper, and a harmon Collins rotor button in the bag[ATTACH] [ATTACH]
[ATTACH] [ATTACH] I have bought a lot of parts at an estate sale lately, I can not figure out what this half mag is used for, any ideas[ATTACH]...
[ATTACH] add one to the list please
Smitty's are what I am looking for, but all I see are Smithy's, are these the same?
I am working on a 1934 Ford Roadster project, very traditional build, flathead powered. The only mufflers that I am currently looking at are...
WELL I know I have 3 good starters now, my problem has moved to the engine, IT IS STUCK! IT HAS BEEN SITTING FOR 15-20 YEARS. would a stuck engine...
Thanks, I tried this and the engine did not turn over, how can I bench test my starter?
[ATTACH] Thanks Bruce, I must have all later model solenoids, still seems to have a heavy spark, and not turning over....
[ATTACH] I have the engine sitting in place, and am getting close to firing it up. I am very confused about this positive ground wiring, when I...
I have purchased a set of Firestone Blackwall Bias Ply tires for my very traditional 1934 3 window coupe. I want to paint or apply some sort of...
No, I have never driven a car with an aluminum flywheel, I here they work better on light weight cars than heavy rides
I cann't find a 10 inch cluch on any websites, sounds like it should be easy to get. Where should I look for a 10 inch 1 3/8, 10 spline cluch, I...
I am building a Flathead powered 1934 Ford Roadster, I have found a very nice Albro aluminum flywheel that i would like to use. I also have a...
Look at this beautiful speedometer that I just found. Iam hoping to put it in my 34 roadster project. I would like to know if anyone knows what...
I reciently bought a Hilborn-Travers early fuel injection unit, it has patent pending cast into the top, and the number 134 stamped at the bottom....
Separate names with a comma.
The Jalopy Journal
