The Jalopy Journal
I have a Harrison KHE 300-usb radio for a 54 ford and scuff plates for a 2 door 54 ford. Both are new still original wrapper and believe radio is...
I put an aluminum shaft out of a crown vic police car, perfect fit.
Actually if you are dealing with carb and distributor and on a budget, Rebel wiring harness serve quite well. I actually spent more money adding...
I used the rebel 9+3 in my car and like everyone says it's easy to use. The wire used in the harness seem to be of good quality, but the fuses,...
Here is EFI Guy's info 303-200--0246 Garred Vance 6051 W. 78th PL. Arvada, CO 80003 Garred is a great guy and usually has an answer to most any...
That's the right link for EFI guy, talk to him, if you want answers that work. I never run mine thru the gears manually, but thinks it will work...
I'm running EFI a 4R70W and 373 pos in my 54, wouldn't have it any other way. I've had the ecu remaped for more horsepower harder shifts and to...
I set my reared 1 degree less the what was measured at the transmission output shaft. My transmission was pointing down 6 degrees so I set my...
Bob Drake sells a tank for the 55 with provision for an oem fuel sender and provisions for an in tank fuel pump. Only thing you have to buy their...
If your talking about an OEM computer and motor I did that very thing. it requires you remap the computer to get rid of the things you won't be...
Mine are mounted just in front of the battery. The whole point is to make the feed wire as short as possible is the way I looked at it.
Man here I have been patting myself on the back and my engine just up and quits. So I think I must be out of gas so I put 5 gallons in the car and...
I had the same problem, finally had to go to an earlier timing cover with the dipstick provision and then used aftermarket power steering and...
No I realized I called the trim by the wrong name and put PS in my post to that effect. I should have deleted it and reposted, will know better...
That's the ones I bought they don't work. I think these may be what I want. Front Door And Fender Moulding Clip - Ford Part # 49-13223-1
From the door post to midway of the front fender you cannot reach to put a nut on the clip. I could remove the inner fenders and get to them, but...
I realize I have the wrong clips now, thanks for your comment
Well I fought these clips or about 40 minutes this afternoon and never managed to get the first one installed, I give up
I really hate asking this question but looking at the clips today and really not sure how to install. The slot is oblong and thought you put them...
If you need new leaf springs I think Posie super glides are the way to go. You can get them with a 3" drop and have no worry about ubolts hanging...
Dave reamed my spindles for me and talking to him changing back to stock springs would raise my front end about 1.5" which I think will be what I...
I've decided that I don't really like the stance of my Vicky. It's lower in the front then the back which is about 6" off the ground. Thinking of...
If you have power steering put in hydroboost and lose the big tub
I've solved my molding clip problems, thanks for the reply, guys.
I used the Hedman Headers on GT40P heads. cylinders 5 and 6 had interference on the spark plug. I could have used shorty plugs and shielded wires...
Received my March bracket today, which matches my alternator bracket. Just need to source the pump and fittings.
There is not a shop here that sells molding clips. It's a 60 mile trip to get them so I was hoping to order them on line, just wasn't sure of part...
On the front fender there are to 6 positions for moulding clips 2 of these I can't use a bolt on clip. This is the only place down the whole side...
The straps I used were for a 55 tank, it's the position of the attachment points. A person could use a bolt coupler and some all thread and use...
I'm sure I'll buy a rebuilt pump just need to find one with returns in somewhat the right direction. Right now leaning toward 1980 K10, $56.00...
Separate names with a comma.
The Jalopy Journal
