The Jalopy Journal
Got it, you & Matt convinced me it’s more agg’s than I want. The 40 Ford pu I have was a nice build done in the ‘90’s driven 500-600 miles then...
Your reply helps. I’d need an adapter or change guts of my torque fire to the small block config. Too much work & expense. Probly pull the 383 &...
383 was in a 1940 Ford Pickup when bought. Several issues, 383 shoe horned into the ‘40 Ford PU, also sat for 30 years indoors w/o starting. Even...
This street rod, a 1940 Ford pickup currently has a 1969 383ci MOPAR. Looking to switch engine only to a 5.7 HEMI. what prefix s/b used?
1- Came across a decent low mileage 2020 configuration 5.7 HEMI. I have a 1969 383 MOPAR hooked to a 727 torque flite. Will the 2020 5.7 bolt up...
what’s the name of the place, I’ll check it out!
Like a wet media blast then paint & or undercoat
In or around Phil’s / S Jersey Anybody know a good place to get frame & undercarriage of a friends 1940 Ford pickup cleaned & coated. Drove it...
I want remove posted classified for my ‘35 Ford. How is it done?
My car is still for sale! Overseas offer / deal didn’t work. Please contact me@ 732 604 2513 for more info!
The Deka intimidator series has one. Thx 57chevymadman
I found that before when shopping @ Advanced Auto. When I see the most important dimension I need as close to 6” width which is a group size 55...
I’ve got a 40 Ford pickup. I had an optimum retool in it for 5 plus yrs that died. Seems the new optimum red top dimensions swelled & I can’t get...
I’ve had an issue w a 2-Holley 94 intake on an Offy intake on my ‘49 V8 Ford Flatheadp. I couldn’t get the idle up high enough without leaving...
Selling my ‘35 Tudor slant back very desirable model! Original body & chassis have 65000 miles. I am the 3rd owner & have the original bill of...
Thx thx
I’ve checked on The Hamb & Safari to find out how to get to classifieds on The Hamb? It says go to classified forum. believe forums is the last...
1967 442 ground lead connected funky. Someone just bared the copper strands & sandwiched them between the power steering bracket. & the engine. I...
I’m looking @ a 1947 Ford PU. It’s running a 302ci ford & has Lincoln Bendix type drum brakes on front but still has original non bendix rear...
New Stat is installed, flow & volume look good. If electric fan working with existing pulley Fan improves cooling I’ll think about a bigger ( more...
Reporting back. I know it’s been a while but I don’t drive the car much as I’m lucky enough to have several that all look & run great. But I have...
‘67 442 came w 2 different water pumps, long for AC & short for no AC, higher volume on AC cars. Does anyone know what supporting parts...
I think grease sounds good. I’ve used before, sealed up nice & easy take apart w/o the hardened goop mess!
Hi all & thx, wacked a few times w a rubber mallet & came right off. Question, I normally goop up the gasket surfaces w my choice of goop but the...
I got a mid ‘60’s Olds 400 engine & replacing the water pump & don’t see bolts holing pulley on it so guessing I need a puller? Tried tapping w...
Don’t think so but w seasoned loud glass packs hard to tell. I’m pretty sure the problem is in the Valve train from sitting so long. It’s always...
Some answers to your questions: Spark plugs & wires new. Distributor is stock non- E-type w new points, plugs, condenser, rotor & cap. tough to...
Separate names with a comma.
The Jalopy Journal
