The Jalopy Journal
You are right Tubman. I called Bob Drake and verified they make their own and are not as thick. I'm going to order one of theirs as soon as I...
Hey guys, thank you for all the responses, I really appreciate it. I'm thinking I will trying sanding process with my next Vintique seal since...
I purchased a new gasket (Vintique #B-700616), and it is so thick it makes my cowl vent look bad sitting above my cowl so much. Does anyone know...
Question for Tim regarding pictures sent. Is your regulator a 3 or 4-bolt mount? I can only see two mounting screws being used in the picture....
Does anyone know what parts (number and supplier), are correct replacements for a 32 5-window rear "roll-up" window? I purchased a "Vintique...
Right and left 5-window coupe doors[ATTACH] , steel aftermarket moldings, no mounting holes, in perfect (new) condition.
These are left and right door for a 5-window. They are steel aftermarket, in great condition (new), but do not have pre-drilled mounting holes....
These are for a 5-window right and left door only, original height. They are aftermarket and do not have pre-drilled holes. Very good condition...
These are 5-window coupe right and left door only. They are aftermarket with no mounting holes drilled and are original height. They are in great...
These are not original 32, they are aftermarket, they are steel, and in "like new" condition. They do not have holes for mounting which may or...
These moldings came with an original 32 body I purchased 2 years ago. My car has a chopped top and these are so clean I didn't want to cut them. I...
These moldings came with an original 32 body I purchased 2 years ago. My car has a chopped top and these are so clean I didn't want to cut them....
I'm looking at this size for my 32 Ford highboy (seems to be a popular size), but have read plus and minus reviews on the ability to properly...
Looking for feedback. I'm building a 32 5-window, original body with a 4" chop. I need all my window hardware and asking for opinions on...
Chief 64; no problem on the high jacking concern. We are all in this together. I hope you get the answer you need. This site and subscribers are...
To Fordors; yes I have the rear channels in place. When you say yours ends 1/2" below the horizontal metal where the wood is enclosed, is yours...
Thank you for the responses. I will look into the Vintique kit and compare with the felt strip I have already purchased. It seems I still need to...
OK, that's what I needed to know. I wasn't sure if the metal channel needed to go all the way up. Thank you!!
I need help from someone who knows what exactly belongs in a 32 Ford 5-window coupe door to hold the window channel in place. I'm attaching a...
Thanks to those who responded to this question. I was able to cut the seal down on the inside where it was hitting the body and this allowed the...
My windshield frame fits perfectly into the body, but as soon as I install the seal that goes around the frame it won't relax against the body....
Perfect and exactly what I was hoping for. Thank you for the feedback!!
Help needed regarding the correct lower radiator hose for my newly built 32 Ford with SBC power. There should be a lot of subscribers out there...
Thanks everyone, I appreciate your feedback on this. I'm going to see how close I can get it in the middle and then likely cut the door frame and...
I'm working to get my door gaps and alignment looking good but don't quite know how to attack one significant problem. The passenger door fits...
A big thank you for all the replies to my question. In trying to answer I will say that I purchased this body and chassis already chopped from a...
I'm sure this has been asked over and over, but does anyone know of good instructions whether video or written on proper body alignment and door...
Thank you "clem" for your response. Pictures are always helpful. It's obvious to me my parts are just not all from the same supplier and therefore...
One more thing; if anyone can attach a picture of their windshield arms attached to the frame in
Thanks guys! As far as the knob, it's on the "A" pillar end and that end is fine, it's just where it attaches to the frame where my concern is. I...
Separate names with a comma.
The Jalopy Journal
