The Jalopy Journal
Friend of mine that paints for a living turned me to this. I called Evercoat and went though the tech line. She couldn't really answer my...
Called and talk to the field rep. He said wit it being a direct to metal application it does seal the metal like epoxy and passes the 500 hour...
So you wouldn't use the super build primer I have? Says it can be used on bare metal.
Why do people use Exopy primer? To seal the metal or some other reason? I ask because I have some of Evercoat Super build that I was going to...
Zip disk? Cut off disk? I've used the dremel with a reinforced cut off weel in hard to reach areas to grind the weld down. Example, the area...
Thank you. Yes I've using some Rustoleum to encapsulate the not so bad areas. The lower portion off the door skin I'm nervous about doing...
You guys got to me... [IMG] [IMG]
He's not painting it, I'm doing all the body work and painting. I want this to be something that I built. He hasn't seen the panels, only of...
Jimmy, Thanks for that. I sprayed some SEM primer on the panel for when I added filler to in hopes stop any rust
This panel isn't bad compare to the other one I replace. I'm assuming the blaster got a little to close in some areas. The panel I replace I...
First time doing patch panels so be easy. This isn't a show truck but it's my truck. Welded in some patch panels for the door. Knowing what I...
Molasses is great if your motor is apart, mine is together. lol I would post pictures of it but I don't want to be crucified
Been removing most of the rust with wire brush on a drill or other rotary tool. Also used small air grinder with roloc 12 grit disk. This may...
fuel line is fuel line. Eastwood sales a tool to straight the line out. Some members have made their own. They just coil it for shipping...
I've use molasses before and it's just a slow process I couldn't see a benefit in using a higher concentrate. I did find this on the youtube....
Thanks guys. Lets say the motor is assembled and been sitting. Now normally we would bag it with some wd-40 on it for added protection or...
Have a motor that has some exterior rust. Runs great and all but having a hard time of how I should prep this in a way that will not ruin the...
Ford 8.8 and 9 use the same crush sleeve?
I ended up tighten the pinion nut and did it to much. Everything came apart on the pinion. New sleeve and bearings tomorrow. Hope to have it...
I'm more of a numbers guy than a feel kinda of guy..haha Gives me reassurance in what I'm doing. The third member is still together. Takeing a...
I forgot to ask is it normal to get a rotation tq number going one way and a different number going the other way? Going counter clockwise I got...
I assume your's is the big bearing end with the seal that goes between the retainer plate and the bearing it self? This is the cheapest I found...
Patrick, It's a factory 31 spline unit out of a 84 bronco/ F-150. I'm just replacing the pinion seal and the pinion support seal. Going to...
So I check the preload with the third member out and it's 6-7 Inch/pounds to rotate. I'm getting another torque wrench to confirm as this one is...
I have my rear end apart now installing new axle bearings, seals, etc. My two questions are 1) When installing the pinion nut back on the torque...
Glad you got it worked out. I see it a lot of LED's flickering because no resister is being used or the wrong resister being used.
No resister will caused flickering.
I trust what you and everyone are saying. I'll probably end up getting a strange engineering kit since 1) they make the Dayton support 2) have a...
Patrick, So you are saying in the picture above they are both set20 just one had the race come out with the bearing while the other bearing's...
https://www.summitracing.com/parts/str-n1914 This pinion support will be good enough?
Separate names with a comma.
The Jalopy Journal
