The Jalopy Journal
Ha ha I know, but I searched online and couldn't figure it out. The first picture in the first post also has a sticker saying it's a model A,...
More pics as requested.
Can you help me ID these two hoods? See attached pics. I can't sell them if I don't know what year, make, and model they are!
So when I removed the distributor wire from the coil, both terminals now read 6v. So does this mean something is grounding out in the distributor?
Not sure I follow.
It's a new condenser. Also new cap and rotor, including the center carbon button.
Yeah I've replaced all of those wires. And the bushing looked perfect.
Yes it is, unless they sold me the wrong one. I've also been trying the original coil too, but it acts exactly the same as the new one.
I set the dual points at 0.017. But even when cranking, there's no change in voltage on the - coil terminal. To my knowledge that will pulse as...
It's a brand new wire. So are all the wires on the top of the distributor.
Looking for some guidance. I've got an old 55' 270 hemi that I'm trying to start outside of the vehicle. I'm not getting proper voltage to the -...
greybeard360, I thought the same...but I can't find one online anywhere!
Ok, goldmountian, you helped unlock the mystery. If that's a horn relay, then I have two horn relays. One for the original horns and one for...
I've got a 1955 Coronet I'm working on getting started again. But I can't properly identify the relay or power distribution block for replacement...
There is an offering for a replacement on eBay: https://www.ebay.com/itm/265090542832?hash=item3db8a0acf0:g:CygAAOSwXu1fQANS
There's a replacement offered on eBay: https://www.ebay.com/itm/265090542832?hash=item3db8a0acf0:g:CygAAOSwXu1fQANS
Need some help interpreting. Here are the parameters I’m going off of from spicerparts.com. The first set of calculations is for my vertical...
What is proper left to right alignment of a driveline? If you can reference articles on this please post. There's lots on pinion angle setup,...
I'm in the process of narrowing the rear axle on my F100, but I'm having trouble identifying what it is. Here's the axle tag code: CITT 4001 J...
Hi guys, I recently wired in new Autometer gauges and a horn. Today while the truck was idling, I had the radio on, air compressors running...
Thank you guys for your help. I was getting 2.4 ohms at the end of the signal wire but 88 at the sending unit's terminal...bad wire. I was using...
What should the resistance be from the signal connection at the tank to ground? Same question for sender mounting bolts to ground?
Once I grounded the tank to the frame and body, nothing changed excepted my resistance dropped to 24 ohms. Any other ideas?
So I just wired up a new set of gauges and everything seems to be working except my fuel gauge. I'm running an Autometer p/n 1424 fuel gauge and...
Yes it was an existing brake system that came with the truck. It's one of their older versions (10-65) and it had tons of gunk inside the MS. I...
Yes very street roddy and goddy. This system came with the truck...the MS is gargantuan and ugly!
I did talk to them, I talked to Eddy. He said I needed to disconnect the rear most line on the MS (which comes from the electric pump) and...
So the MS was working before I ran all new lines. I put it all back together, bled it, but my pedal would go to the floor if I kept constant...
Hi everyone, Need your help. I'm running an electric brake system from abspowerbrake.com and can't get the brakes to bleed properly. You're...
Here's what I've got
Separate names with a comma.
The Jalopy Journal
