The Jalopy Journal
Can someone tell me what size the VIN numbers should be on a 1934 Ford. ( 1/8", 1/4", 3/16" ??) And did they include the Stars on each end? A...
I'm planning to c notch a '34 frame 2 " to allow more travel for an 8" Ford differential. Any recommendations on what size round steel pipe to...
Can anyone tell me who makes and sells this dashboard? Sorry, I can't figure out how to attach the picture!!!! or delete a post........
This may sound crazy, but I would like to know if anyone has put perches on both sides (top and bottom) of the differential while swapping rear...
I use the B & M adjustable lock up controller and like it a lot.
1946 Sedanette (this one may be available)
Many thanks!
Is it possible to replace the front differential seal on a 1957 Chev rear end with the "pumpkin" still in the housing? Are there any special tools...
Can anyone recommend a good Hot Rod Appraiser in SO CA that can appraise a Vintage Hot Rod?
Ok, so I have determined that the column is definitely Ford. I have also found out that the bottom "bearing" that I thought needed replacement, is...
Thanks for all the input so far..................the tilt is the same handle as the blinker handle, you push toward the dash and the column tilts....
I have this column in my 29 A. The bottom bearing is shot and I need to replace it. First I need to know what the column is out of. I was told...
My model A has 56 Ford drum brakes in front, 57 Chev drum in the rear. It has a 62 Chev single(1 1/8" bore) firewall mounted master. The pedal...
Lock up is a must. I first intstalled a 200R without it and ended up putting one in later. I run the B & M adjustable lock up control and it works...
Thanks again for all the help. My housing uses the 6 cyl Chevy water pump. This unit was on a car a had 15 years ago and never had a...
The pictures you posted are exactly what I started with, assuming the one pictured is cast iron. I'm just going to have to drill and install my...
Thank for all your help. I am attaching pictures of my pump housing. As you will see there is no screw hole for any type bleeding device. I...
Thank you for all of the replies! The unit I have is over 20 year old, no bleed screw, and not even the cast-in flat area where it should go. I do...
I have an old Zip's water pump ( I cut off the alt, air brackets) that does not have a bleed valve. I have it installed with a heater in line. I...
Can anyone tell me what the idea fuel pressure is for a Holley 2110 Carb? :rolleyes:
What is the best way to make a new alternator look old? Someone told me to use over cleaner?????Any suggestions?
I want to run an old Nicson 3 X 2 manifold on a 290 H.P. Chevy crate motor. It looks like the ports are much smaller on the intake than on the...
On a 1973 Cadillac fuel pump there are 2 outlets on the bottom. Can anyone tell me what the smaller one is used for? Can I just cap it off?
I know it is preferreable to run a volt meter instead of an Amp meter, but I want to use the stock gauges. My question is when running a high...
Can someone tell me how to remove the shift handle from the unit? I need to bend it to get it closer to the dash as all the "built-in" adjustment...
When you adjust it in will it change the steering wheel position?
I have some play in my steering wheel and want to try to adjust the slack out. I noticed an adjustment screw on top of the box. Can I safetly...
Real driver!
I'm kinda attached to this one!
Situation: trans fluid backing up dip stick tube and spilling out. I am close to getting my car on the road and have driven it from my garage to...
Separate names with a comma.
The Jalopy Journal
