The Jalopy Journal
anyone know ohio's laws on red window tint ?
Does anyone know anything about this wheel balancer.....notice it has a air hose connected to it....thanks for any information...
does anyone have a 1962 nationals program or participants list that would copy the list and sell it to me.......please let me know.......thank...
Plan on going to dragway 42 rock and race event, in july 2012 ..... who's going......has it been a good way to spend a weekend... Thanks for any...
I would letter it. Draws attention from the old racers in the crowd. Car shows, cruise ins are are full of flamed cars. shiny cars, rat rods and...
i will be in ocala florida friday feb. 11 and sat. feb 12......are there any cruise ins or car shows there.......just passing thur, but i like to...
thanks for the information guys.........i know the muncies 3 speeds weight about 20-25 lbs more than saginaw 4 speeds.....also the gears are wider...
would like to know what years the heavy duty mc1 muncie 3 speed were used ........i know they were in '69 carmaros etc...were they also used in...
is this a good sized meet......do they have a building that is heated..... thank you charlie
i have a early '70's camaro rear end in my willys......i thought it is a 3:55, but i don't see any ring and pinion sets at 3:55 available....it is...
local engine builder here uses the PBM brand of camshaft......anyone had good luck with that cam......model #140-132 453 lift , 284...
thanks guys, guess i'm getting too old for this engine building stuff......i really thought i had a great idea.......lately, everything i touch...
i have a large journal 60's 283 block that is good......i also have a 307 large journal good crankshaft and .060 pistons and rods from the 307...
can i use a used flat lifter cam with new lifters with any sucess.....especially if i use zinc in the oil......??? thank's, charlie.........
anybody ever put a thumper cam (smallest) in a stock 305......trying to use some old stuff in a rat rod....... thanks, charlie.........
do shim steel head gaskets raise compression and what should they be coated with.......anybody use them ??? thanks in advance for the...
:confused:i bought a 307 sbc boat motor for cheap, complete, pulled heads and found very little wear or sludge.......has deep oil pan, pistons...
has anyone used the summit or jegs brand rod or main bearings, lowest price.......from the description given they the KING BRAND made in ISRAEL...
putting a 283 ('67) rebuild together, found i had a bad crankshaft....bought a good used cast iron crank, but it is not drilled for a bolt for the...
thanks guys, now i will use the 3 bolt starter.......chascue.....:)
have a '63 283 engine......using an old 1957 manual bellhousing so i can change the clutch without pulling bellhousing........'57 starter came...
anybody use a summit k1103 cam or a k1102 in an rebuilt stock 283 ....i want it driveable (street) with saginaw 4 speed and 3:55 rear...
i currently have 2 fin type trans cooler for my willys, mild street rod engine......turbo 350.......would like to remove small fin cooler near...
anyone know where to buy a buick 350 manual flywheel........htanks
anyone know a phone number or address for chuck finders.....thanks in advance
whats the most sensible fluid to use in a parts washer i just bought.....its in a garage attached to the house......will just be used off and...
will older sbc short water pumps fit 1986 and newer engine blocks.....thanks, charlie
i go to all the nostalgia drags within 400 miles of me, see gassers that i love and strong super stock cars , neat, fed and funny cars etc....are...
which is easier to cool, '77 buick v6 oddfire or '85 chevrolet 4.3 v6....i have both and may put one in '37 willys i have.......do'nt want to cut...
from ohio, have '41 willys 4 door sedan street rod, grey primer with names painted on doors....sbc, turbo 350..pictures have been in magazines...
Separate names with a comma.
The Jalopy Journal