The Jalopy Journal
they stole them for scrap more than likely. someone who knows what they are wouldnt take them out of respect. like i said someone stole them...
drill and tap 2 holes 180 degrees from each other in the drum preferably on or close to the axle flange. spray some penetration oil inside to get...
Nobody wil make these tires anymore for safety reasons. Changes in technology and tire compounds have had to change for legal purposes. its kind...
6 to 1 ratio of white vinegar and water. vinegar is pretty much a mild form of bleach but not harsh enough to remove any kind of dye. it works...
your rods are extremely important blower compression will destroy them pretty easy. spend all your money on your bottom end, then you can upgrade...
clean them first and dirt or debris can cause them to rust. spray them with penetrating oil something that isnt water based like some of them are....
bearing clearances wont make that kinda pressure thats pretty insanely high. If you rebuild a pump or have a high flow pump the bypass can be...
My mom bought one a couple of years ago and its sitting in the pantry. Thats exactly what its for, if its not booze related my mom doesnt buy it.
yeah i wasnt sure if it was a thick casting or not. some of the thinner castings can have heat problems when you take too much out of the cylinder...
I dont know how safe it is to go .090 over on a 318. It would be more easily done and not decrese the longevity of the block as much if you used a...
well i got if apart now and there was previous damage. due to the fact that someone had already rebuilt it and didnt do a complete job. Personally...
sawy bar is definately needed if your going to drive on the street. it ties the lower control arms together without it they will want to drive...
this is a 68/69 M22 from a chevelle, Nova, or camaro. everything in the inside and case numbers check out as to that being what it is. I'm not...
an auto is going int he chevelle. the muncie is for Nick32Vic. i plan on doing it the right way, i just want to do it without damaging any other...
Im rebuilding an M22 right now, and im having some major problems. I opened the case everything looks good my only problem was a bad syncro. well...
You are running too hot reguardless of a fan or not. to be completley honest you should run cooler than that on the highway without a fan as long...
I wouldnt say that this engine would fall into the mildy built category. it sounds gnarly to me.
chuck palahniuk books if you like they whole fiction, thrillers, and the down right gnarly. Henry Rollins writes a good book too.
i dont know a whole lot about flatheads, actually i know nothing about any of the specifics. i was only able to get to lift partially disassembled...
you will get a ping and spark knock out of this world. it wont happen with 12:1, its too much for that combo to run pump gas. like said before you...
A teacher of mine has an old forklift thats been sitting out behind the shop for a while eqipped with a Chrysler Flathead. I havent really dug to...
just remove the PCV valve and add an oil catch can. you can get them on ebay really cheap. it will take care of most of the problem, and it will...
ive actually taken a pencil and snapped it in half and used it the same way. it works pretty good.
muratic acid for a couple of miuted works pretty well. it also takes the coating of fasteners too.
you can use a hammer and a sharp chisel and it gets the job done too.
well with the addition of oxygen which is really what n2o offers because nitrogen isnt volatile cylinder pressures increase but very little. as...
well when it was first introduced it was used basicly in primitive injection system. it was used in aircraft because at high altitude because low...
I see alot of people who build their rods to race useing blowers, but not so many useing nitrous. its been used on automotive engines since the...
well if it had anything to do with the vacuum advance when you got over 2500 it wouldnt get any better or smooth out any. if the timing cant...
depending on the firing order of the cylinders is going to depend on if the modifications will help. if the cylinders fire in sequence with each...
Separate names with a comma.
The Jalopy Journal
