The Jalopy Journal
3.36 sounds like a 10 bolt gear. Should be 3.31 in a 12 bolt. I would double check before I spent the money.
From the research I have done so far I can use the distributor from any rochester setup. I wont need the tach drive though but an old cable drive...
Bought a 57 Nomad last weekend that came with a 58 fuel unit that I would like to install. Missing the distributor. Any one have a line on one...
1957 Belair 4 door sedan with lots of extra parts. Has an original power pack 283 with a swapped in turbo 350. Engine turns over but haven't...
bump
Very rough 55 Chevrolet 2dr sedan. Has 327 with 1 double hump head and 3 speed manual with hurst shifter. Has seat springs for front and rear...
To remove the front pump take all of the bolts out of it and look for two holes that have threading in them. Thread two short 3/8 coarse thread...
I think the speedway will fit. The first set I had had clearance issues with the steering box in the stock location. The coated ones I bought fit...
One owner 69 Camaro RS/SS 396 4 speed car that had been tapped on every corner by drunk owner over the years but totally stock for $600 in 1984....
Liking the looks of this build. From the positioning of your engine I am thinking the Hooker big block Chevy 2 headers would probably fit. Two...
Very very cool!!! Diggin the paint and slot wheels. Can't wait to see this one cleaned up and going again. What brand are the wheels? I can't...
We snagged a 65 409 out of a c80 Chevy truck a few years ago and have a 65 dated 409 well engine. Really good buy for $100 especially if it came...
Take your torch and some water with you and remove the wheel and just cut a circle just outside the center hub through the brake drum. Works...
Great looking start. I am a little biased but 55's are really hard to beat in any form.
Been watching the proxibid for a while on this sale and decided to skip the auction. 1955 Chevy 210 2dr sedan with no front floor pan for...
A guy I know used to be a road delivery guy and delivered parts to this dealership over the years. He said Lambrecht got in on the ground floor...
I love all three but my first car was a 56 so I will say 56 first. Really like 55 Nomads with the one year only radiused wheel wells. Been driving...
Unreal skills to put some of those back together. I can see fixing the convertibles/coupes but can't imagine putting that much effort in to a 4...
Mopar guys spend big bucks for certain items and your 4 speed might be one of them. I would do some research on the trans and try to get a value...
Get her bought. Should be able to find a 55-57 Chevy decklid for cheap or maybe a 57 Pontiac 4dr parts car to rob. I am thinking the Pontiac...
I just installed a rotary revolution 10k and it makes that thing look weak. Had a 6000 pound Tahoe on it the other night and it didnt act...
Way to go Butch!!! See you at the KKOA Salina.
Great find, I bought a 63 Impala 4dr parts car at an auction a few years back for $100 and as we were winching it up on the trailer I spotted the...
Not really cheap unless you get lucky but I have beat the stuffing out of my M20 Muncie in my 56 gasser. Shattered the drive shaft slip yoke at a...
Not a bad looking 55 for 9 bills. Looks to be a 150 also so no messing around with stainless. Go ahead and radius it if that is what you are...
If you truly have an L79 327 Chevy never offered an automatic behind this engine. I would want a 4 speed manual to make the 327 sing!!!
I have a 55 and 56 Chevys with Lakewood bellhousings that bolt up to the stock 55-57 bellhousing mounts. They have a flat area formed in where...
Here is a pic of my 56 with Chevy 2 oil pan and chevy 2 pitman arm. It gets close at lock on either side but it works.
Radius the wheel wells, big slicks, raised front end with skinnys "gasser" Ok I just had to say it to get it out of my system. 1967 air in the...
I had this issue on my 56 straight axle car. I used a 62-67 nova pan because I had one and it is a lot squarer in the front to give more...
Separate names with a comma.
The Jalopy Journal
