The Jalopy Journal
here's a few more of that pickup, the chop is midway of the middle and upper door hinges , you will have to cut the windshield, door glass and...
thanks for the bump. yes it's been around 15 years since i first met lance and helped him build that pickup. with it still being our most...
thats something i would like to know for sure as i only have the stock GM part number, one thing i know is in 1962 when gm came out with a 194/230...
funny toyota fork lifts also used them for a while, generac , kohler, water pumps also used them
standard 1.5 ratio gm SB rocker. part number 05723551. IMMO they would be a waste of money, motor only turns a tad over 5k before dropping...
base engine in the 1500's how many decades has gm used that china/ cherry made engine in the smaller suv's now?
i have found they don't respond well being over fueled 450 cfm tops run great on a single two barrel , as to the later small port heads ,gm...
that would be nice to know more about as the latter gm industrial/marine were all 8 port heads, some had efi with port injection for which gm...
origin engines had that one 3.6 liters https://originengines.com/origin-engines-3-6l/ and nothing more since that shown, it would have been...
here's shots of jersey suedes home made mounts motor wise yes the 151 heads fits and raises the compression ratio to that of what GM built the...
adding a pfd with the specs the trick we found was to find a lift truck motor with the stamping LW6 so you have the 10.5 engine rebuild it with...
bumping this back to life after a email saying someone had.asking if a marine intake had been cut up to use. my answer is yes and don't waste the...
sorry but i can't find the post i got a email about asking if anyone cut up a marine manifold set and the answer is YES, sorry it can't be used ,...
that happened to be a V4, made out of a 283 so he could stay in the class
you could try . http://www.vanpeltsales.com/index.htm
with both knees worn out from 50 years of fixing cars in dealership shops.skiing hard and kick starting a pan head , i can attest that we can...
merc v8's were not 8ba's they were 9cm's 2 97's they ran fine, when we ran 3-97's they tended to over fuel
my point was for the compression ratio, 62 cc small valve made 10.5 the 64 cc which used the unshrouded 2.02 intakes heads made for 10.25...
northern/bergen county nj guys, we lost another old time hot rodder/body man on april 19th 2024 Carl Borntrager from maywood. owner of rochelle...
sorry for the very late reply, 327 with flat top's using 64 cc 462 heads is more like the specs of the 327/300hp compression in that motor was...
another old timer thinking about the past years who is the same age as you. i was one of the lucky who worked part time for pappy and learned a...
not that i have ever seen, ran a 54 belair ,235 in N/stock for years never spun a bearing
my writers had to go out and record the mileage and look the car over for damage and record it, when checking in the car, you would be surprised...
american auto wire sells a lot of plug kits check out their web site .another is https://www.delcity.net/
chevy man building a ford?
my understanding was ford did not vin stamp the engines as they knew those would wear out and be replaced, they did stamp the trans to the frame...
32 todor , k code 289, c4, 4 bar coil over rear ,
those are beyond being used, pitted to badly, if your worrying grab a set from summit or jegs about $110.00 a set of 16
guess we were lucky, the car sat on the factory rails ,
sorry guys but there are a few cars i can't see rodded, and a baby bird or a 53 or 54 vette are two of them as to finding a good y block core,...
Separate names with a comma.
The Jalopy Journal
