The Jalopy Journal
Maybe check out this thread - might be as close as you find to your Buick...
No offence to anyone, but stay away from airbagit.com. I have bought numerous kits from thorbros.com. Regardless of where you buy, stick with name...
Found this link on google: http://www.plumbingsupply.com/brass.html About half way down, they are called face/flush bushing, but limited selection...
I have come across steel versions of those with electrical conduit, specifically around explosion proof and rugged/environmental boxes and...
On my 60 Buick, I used a rear end from a donor 74 Monte Carlo, arms and all. I cut the lower brackets off the diff and swapped them side to side...
For electric fans, I believe the best location for the sensor is in the rad - that is where the coolant you are cooling is. If that is not...
Don't get buried by the details! I installed one of these on every setup I have had a hand in, just to get home in the event of a problem. I...
Reality is though, your pressures may not be where you left them after a couple of days!! Best to compare tank measurements to figure out what...
Not familiar with Helix compressors, but that is a small tank for front and back. You may not get more than a single lift with that size,...
Wouldnt mind picking over that 53/4 Pontiac - where abouts is this?
I always set my personal cars up to lay out, but as I start to do work for people who have no experience at all with air ride, and some for...
Personally, I would say 8 valves for sure. Any time you tee anything you have the opportunity to get roll. If you want to run only 2 switches,...
My 62 LeSabre.
My oldest two the day I brought home my Olds. They advised me on the best way me unload it off the trailer and then helped me hose out the inside...
I seem to think that for the master cylinder you mentioned that the output for the rear to and from the proportioning valve will be 1/4. It will...
To run them centered and without vibration, my though would be to source a hub-centric spacer to make sure the wheel fits centered on the hub (as...
I am in no way experienced in upholstery, but I bought a JUKI LU563 in the local classifieds for around $500 to do exactly what you describe. This...
The 3M is pretty bulletproof. On a project some time ago I had coated the floor pans with it - stood up to a last minute clearance issue corrected...
X2 with the S10 setup. I am using a 95 2.2L master/slave and it is a sealed unit - no bleeding required, but you'll be limited in distance between...
I made a new thicker bolt in plate at the top of the firewall to mount my master/booster on my 54 (replaced the sheet metal one that originally...
That is a very common bolt pattern, especially on imports (Honda, Toyota). Your problem will be the offset - you probably dont want a FWD offset...
I was working in a truck tank shop and while walking between bays, I stepped on an air line. Guess the line was loose where it connected to the...
Have a look at 90's GMC trackers - those little 4X4's. I believe they have this bolt pattern, and would have fairly narrow wheels. Only problem is...
I had a similar issue, and found a web site called parts train. There I was able to get dimensions, pictures and capacities of many tanks....
Hey from Keswick. Cruised up to Beaverton in my 60 almost every weekend this summer with the kids to picnic down by the lake. Crusty pizza is the...
I de-soldered my top tank as all teh tubes were blocked. Made a tool out of sheet betal to run through them all and soldered it back on with...
Careful with brake clean - seriously http://www.jalopyjournal.com/forum/showthread.php?t=384338&highlight=brake+cleaner+hazardous
Hey oj, So are you saying that I could wire this machine on the same line as my MIG uses (50A 12AWG) and weld most things i would need (20 gauge...
Thanks for the input everyone. Ok, so this thing is a beast. Requires 4 AWG input power cable and a 140 amp breaker according to the manual. This...
I've looked at a lot of threads reading up on tig welders, and though I dream of Millers and Lincolns, in my area, new is all that I seem to come...
Separate names with a comma.
The Jalopy Journal
