The Jalopy Journal
Great idea. I will do that, but according to the chart, says these Monroe shocks are for Motor Homes?
Monroe 55502 8.63 compressed 12.75 extended travel 4.13 55503 9.63 compressed 14.75 extended travel 5.13...
I can see what you mean. Thats a lot of info, but very good, just what I was looking for, THANKS Jack
The rear is 8.75 MoPar.
Need to replace rear shocks on my DeSoto Hot Rod. The shocks that are on the car now, no longer availabe. They are KYB Gas a Just. Need help from...
Cleaned plugs and reinstalled, until I get my new plugs and wires.
1st. Yes 3rd. No, close to 100000 miles. Talked to Eric at Hemi Hot Heads, he advised common the tube (head end) gets out of shape over time....
Pulled my plugs yesterday, oil on the plugs and contacts on all plugs, and the poreclain black. Oil pressure good, 50 at 60 MPH, 40 at idle, 60...
gEEz, what the Hell? Whatever it is, don't think it's something I need. Thanks anyway. Going with Squirrels method and a vacumn gauge.
I am running 2 - 500 cfm Edelbrocks on my 1st Gen 392 Hemi in my HotRod How to adjust fuel mixture idler screws. Have seen on here how to abjust...
Thanks, great info. Firing order same as SBC Chevy, right?
Clockwise. I turned distributor clockwise, and now sometimes when I start a cold engine, it back fires thru the carbs. 2 500 cfm Edelbrock...
Mostest Stupidest Question Ever? Is the 1st Gen 392 considered Small Block or Big Block? Which way to rotate the Distributor to retard the...
Me too. Great info, RTV it is. The gasket is cork, and it's 4 pieces. Could not find a 1 piece rubber gasket for the 1st Gen 392 Hemi, or a 1...
Would this (anaerobic) work better, or as good as, RTV on an oil pan gasket?
Well vented K&N filler cap. Did have PCV, but when I went back to original valve covers, no breather, but it was leaking with the PCV. Defiently...
??? Never heard of it. Give me more info please. Is this something I can get at my local parts store?
Will not know for sure until tomorrow when oil pan gasket arrives from Hot Heads. The other 3 times, crank was smooth, so hope no machining needs...
Tommy, That is the info I have heard most. I am going to install the seal flush with the bearing cap. This makes my 4th attempt to stop that seal...
Have 2 questions about removing and installing 2 piece Neoprene rear main seal in 1st Gen 392 Hemi? 1. Do you recommend installing seal flus with...
Absodamnedlutely. Don't really know what it is suppose to feel like being 78 (this is my 1st time). Main difference, getting up and down, taking...
Late to the party, as usual, but better late than never. Wish I had seen it several years ago. Not to mechanically inclined, especially wiring....
Agree. Contacted Rebel, they responded immediately, and I understood it completely. 2 thumbs up for Rebel customer service. Jack
After everyone's input here, I have decided, "what the hell", I think I'm give it a try. Either going to go with the, GM, Rebel, or Ron Francis....
Had never heard of Rebel, but if support is good, and can understand what they are saying, that is a BIG plus.
Lotta good info here. Took a while, but have figured out, those connectors with the plastic covering is about as useful as tits on a rain barrel....
Good connections (connectors) is like finding good hose clamps, not possible.
Trust me, I do. Have driven for 20 years, about 91000 miles. Everytime I do something under the dash, I will accidently unplug something that I...
Thank You, Jack
Separate names with a comma.
The Jalopy Journal
